linux-edison.git
12 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Linus Torvalds [Fri, 24 May 2013 15:27:32 +0000 (08:27 -0700)]
Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:
 "It's been a while since my last pull request so quite a few fixes have
  piled up."

Indeed.

 1) Fix nf_{log,queue} compilation with PROC_FS disabled, from Pablo
    Neira Ayuso.

 2) Fix data corruption on some tg3 chips with TSO enabled, from Michael
    Chan.

 3) Fix double insertion of VLAN tags in be2net driver, from Sarveshwar
    Bandi.

 4) Don't have TCP's MD5 support pass > PAGE_SIZE page offsets in
    scatter-gather entries into the crypto layer, the crypto layer can't
    handle that.  From Eric Dumazet.

 5) Fix lockdep splat in 802.1Q MRP code, also from Eric Dumazet.

 6) Fix OOPS in netfilter log module when called from conntrack, from
    Hans Schillstrom.

 7) FEC driver needs to use netif_tx_{lock,unlock}_bh() rather than the
    non-BH disabling variants.  From Fabio Estevam.

 8) TCP GSO can generate out-of-order packets, fix from Eric Dumazet.

 9) vxlan driver doesn't update 'used' field of fdb entries when it
    should, from Sridhar Samudrala.

10) ipv6 should use kzalloc() to allocate inet6 socket cork options,
    otherwise we can OOPS in ip6_cork_release().  From Eric Dumazet.

11) Fix races in bonding set mode, from Nikolay Aleksandrov.

12) Fix checksum generation regression added by "r8169: fix 8168evl
    frame padding.", from Francois Romieu.

13) ip_gre can look at stale SKB data pointer, fix from Eric Dumazet.

14) Fix checksum handling when GSO is enabled in bnx2x driver with
    certain chips, from Yuval Mintz.

15) Fix double free in batman-adv, from Martin Hundebøll.

16) Fix device startup synchronization with firmware in tg3 driver, from
    Nithin Sujit.

17) perf networking dropmonitor doesn't work at all due to mixed up
    trace parameter ordering, from Ben Hutchings.

18) Fix proportional rate reduction handling in tcp_ack(), from Nandita
    Dukkipati.

19) IPSEC layer doesn't return an error when a valid state is detected,
    causing an OOPS.  Fix from Timo Teräs.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits)
  be2net: bug fix on returning an invalid nic descriptor
  tcp: xps: fix reordering issues
  net: Revert unused variable changes.
  xfrm: properly handle invalid states as an error
  virtio_net: enable napi for all possible queues during open
  tcp: bug fix in proportional rate reduction.
  net: ethernet: sun: drop unused variable
  net: ethernet: korina: drop unused variable
  net: ethernet: apple: drop unused variable
  qmi_wwan: Added support for Cinterion's PLxx WWAN Interface
  perf: net_dropmonitor: Remove progress indicator
  perf: net_dropmonitor: Use bisection in symbol lookup
  perf: net_dropmonitor: Do not assume ordering of dictionaries
  perf: net_dropmonitor: Fix symbol-relative addresses
  perf: net_dropmonitor: Fix trace parameter order
  net: fec: use a more proper compatible string for MVF type device
  qlcnic: Fix updating netdev->features
  qlcnic: remove netdev->trans_start updates within the driver
  qlcnic: Return proper error codes from probe failure paths
  tg3: Update version to 3.132
  ...

12 years agoGFS2: Fix typo in gfs2_log_end_write loop
Steven Whitehouse [Tue, 21 May 2013 11:49:07 +0000 (12:49 +0100)]
GFS2: Fix typo in gfs2_log_end_write loop

There was a missing _all in this loop iterator

Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
12 years agoGFS2: fix DLM depends to fix build errors
Randy Dunlap [Tue, 14 May 2013 17:02:48 +0000 (10:02 -0700)]
GFS2: fix DLM depends to fix build errors

Fix build errors by correcting DLM dependencies in GFS2.
Build errors happen when CONFIG_GFS2_FS_LOCKING_DLM=y and CONFIG_DLM=m:

fs/built-in.o: In function `gfs2_lock':
file.c:(.text+0xc7abd): undefined reference to `dlm_posix_get'
file.c:(.text+0xc7ad0): undefined reference to `dlm_posix_unlock'
file.c:(.text+0xc7ad9): undefined reference to `dlm_posix_lock'
fs/built-in.o: In function `gdlm_unmount':
lock_dlm.c:(.text+0xd6e5b): undefined reference to `dlm_release_lockspace'
fs/built-in.o: In function `sync_unlock':
lock_dlm.c:(.text+0xd6e9e): undefined reference to `dlm_unlock'
fs/built-in.o: In function `sync_lock':
lock_dlm.c:(.text+0xd6fb6): undefined reference to `dlm_lock'
fs/built-in.o: In function `gdlm_put_lock':
lock_dlm.c:(.text+0xd7238): undefined reference to `dlm_unlock'
fs/built-in.o: In function `gdlm_mount':
lock_dlm.c:(.text+0xd753e): undefined reference to `dlm_new_lockspace'
lock_dlm.c:(.text+0xd79d3): undefined reference to `dlm_release_lockspace'
fs/built-in.o: In function `gdlm_lock':
lock_dlm.c:(.text+0xd8179): undefined reference to `dlm_lock'
fs/built-in.o: In function `gdlm_cancel':
lock_dlm.c:(.text+0xd6b22): undefined reference to `dlm_unlock'

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
12 years agoGFS2: Use single-block reservations for directories
Bob Peterson [Tue, 14 May 2013 17:04:29 +0000 (13:04 -0400)]
GFS2: Use single-block reservations for directories

This patch changes the multi-block allocation code, such that
directory inodes only get a single block reserved in the bitmap.
That way, the bitmaps are more tightly packed together, and there
are fewer spans of free blocks for in-use block reservations.
This means it takes less time to find a free span of blocks in the
bitmap, which speeds things up. This increases the performance of
some workloads by almost 2X. In Nate's mockup.py script (which does
(1) create dir, (2) create dir in dir, (3) create file in that dir)
the test executes in 23 steps rather than 43 steps, a 47%
performance improvement.

Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
12 years agoGFS2: two minor quota fixups
Bob Peterson [Fri, 10 May 2013 15:59:18 +0000 (11:59 -0400)]
GFS2: two minor quota fixups

This patch fixes two regression problems that Abhi found in the
GFS2 quota code.

Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
12 years agoARM: at91/sama5: fix incorrect PMC pcr div definition
Josh Wu [Thu, 23 May 2013 10:18:48 +0000 (10:18 +0000)]
ARM: at91/sama5: fix incorrect PMC pcr div definition

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
12 years agoARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definition
Boris BREZILLON [Thu, 23 May 2013 16:01:21 +0000 (18:01 +0200)]
ARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definition

The PA24 pin is wrongly assigned to peripheral B.
In the current config there is 2 ETX3 pins (PA11 and PA24) and
no ETXER pin (PA22).

Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> # 3.8+
12 years agoARM: at91: at91sam9n12: move external irq declatation to DT
Jean-Christophe PLAGNIOL-VILLARD [Thu, 23 May 2013 22:59:16 +0000 (00:59 +0200)]
ARM: at91: at91sam9n12: move external irq declatation to DT

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
12 years agopowerpc/pseries: Make 32-bit MSI quirk work on systems lacking firmware support
Brian King [Wed, 22 May 2013 11:07:46 +0000 (11:07 +0000)]
powerpc/pseries: Make 32-bit MSI quirk work on systems lacking firmware support

Recent commit e61133dda480062d221f09e4fc18f66763f8ecd0 added support
for a new firmware feature to force an adapter to use 32 bit MSIs.
However, this firmware is not available for all systems. The hack below
allows devices needing 32 bit MSIs to work on these systems as well.
It is careful to only enable this on Gen2 slots, which should limit
this to configurations where this hack is needed and tested to work.

[Small change to factor out the hack into a separate function -- BenH]

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
12 years agopowerpc/powernv: Build a zImage.epapr
Benjamin Herrenschmidt [Tue, 21 May 2013 23:00:22 +0000 (23:00 +0000)]
powerpc/powernv: Build a zImage.epapr

The zImage.epapr wrapper allows to use zImages when booting via a flat
device-tree which can be used on powernv.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
12 years agopowerpc: Make radeon 32-bit MSI quirk work on powernv
Benjamin Herrenschmidt [Tue, 21 May 2013 22:58:21 +0000 (22:58 +0000)]
powerpc: Make radeon 32-bit MSI quirk work on powernv

This moves the quirk itself to pci_64.c as to get built on all ppc64
platforms (the only ones with a pci_dn), factors the two implementations
of get_pdn() into a single pci_get_dn() and use the quirk to do 32-bit
MSIs on IODA based powernv platforms.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
12 years agopowerpc: Context switch more PMU related SPRs
Michael Ellerman [Tue, 21 May 2013 16:31:12 +0000 (16:31 +0000)]
powerpc: Context switch more PMU related SPRs

In commit 9353374 "Context switch the new EBB SPRs" we added support for
context switching some new EBB SPRs. However despite four of us signing
off on that patch we missed some. To be fair these are not actually new
SPRs, but they are now potentially user accessible so need to be context
switched.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
12 years agopowerpc/powernv: Fix condition for when to invalidate the TCE cache
Benjamin Herrenschmidt [Mon, 20 May 2013 17:25:15 +0000 (17:25 +0000)]
powerpc/powernv: Fix condition for when to invalidate the TCE cache

We use two flags, one to indicate an invalidation is needed after
creating a new entry and one to indicate an invalidation is needed
after removing an entry. However we were testing the wrong flag
in the remove case.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
12 years agopowerpc/pci: Fix bogus message at boot about empty memory resources
Benjamin Herrenschmidt [Mon, 20 May 2013 17:24:39 +0000 (17:24 +0000)]
powerpc/pci: Fix bogus message at boot about empty memory resources

The message is only meant to be displayed if resource 0 is empty,
but was displayed if any is.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
12 years agopowerpc: Fix TLB cleanup at boot on POWER8
Benjamin Herrenschmidt [Mon, 20 May 2013 17:23:22 +0000 (17:23 +0000)]
powerpc: Fix TLB cleanup at boot on POWER8

The TLB has 512 congruence classes (2048 entries 4 way set associative)
while P7 had 128

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
12 years agodrivers/crypto/nx: Fixes for multiple races and issues
Kent Yoder [Fri, 12 Apr 2013 17:13:59 +0000 (17:13 +0000)]
drivers/crypto/nx: Fixes for multiple races and issues

Fixes a race on driver init with registering algorithms where the
driver status flag wasn't being set before self testing started.

  Added the cra_alignmask field for CBC and ECB modes.

  Fixed a bug in GCM where AES block size was being used instead of
authsize.

  Removed use of blkcipher_walk routines for scatterlist processing.
Corner cases in the code prevent us from processing an entire
scatterlist at a time and walking the buffers in block sized chunks
turns out to be unecessary anyway.

  Fixed off-by-one error in saving off extra data in the sha code.

  Fixed accounting error for number of bytes processed in the sha code.

Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
12 years agoARM: dts: imx: fix clocks for cspi
Jonas Andersson [Thu, 23 May 2013 11:38:05 +0000 (13:38 +0200)]
ARM: dts: imx: fix clocks for cspi

The CSPI controller has only one clock, but the driver spi-imx.c needs
clock "per" to calculate bitrate divisor.

Signed-off-by: Jonas Andersson <jonas@microbit.se>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
12 years agobe2net: bug fix on returning an invalid nic descriptor
Wei Yang [Wed, 22 May 2013 15:58:22 +0000 (15:58 +0000)]
be2net: bug fix on returning an invalid nic descriptor

In function be_get_nic_desc(), it will go through the descriptor array
returned from f/w. By comparing the desc_type field, it determines whether
there is a nic descriptor in the array or not. In the case of no nic
descriptor, this function should return NULL.

The code may return an invalide descriptor, when there is no nic descriptor
in the array and the desc_count is less than MAX_RESOURCE_DESC. In this case,
even there is no nic descriptor, it will still return the lase descriptor
since the i doesn't equal to MAX_RESOURCE_DESC.

This patch fix this issue by returning the descriptor when find it and return
NULL for other cases.

Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agocgroup: fix a subtle bug in descendant pre-order walk
Tejun Heo [Fri, 24 May 2013 01:50:24 +0000 (10:50 +0900)]
cgroup: fix a subtle bug in descendant pre-order walk

When cgroup_next_descendant_pre() initiates a walk, it checks whether
the subtree root doesn't have any children and if not returns NULL.
Later code assumes that the subtree isn't empty.  This is broken
because the subtree may become empty inbetween, which can lead to the
traversal escaping the subtree by walking to the sibling of the
subtree root.

There's no reason to have the early exit path.  Remove it along with
the later assumption that the subtree isn't empty.  This simplifies
the code a bit and fixes the subtle bug.

While at it, fix the comment of cgroup_for_each_descendant_pre() which
was incorrectly referring to ->css_offline() instead of
->css_online().

Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: stable@vger.kernel.org
12 years agotcp: xps: fix reordering issues
Eric Dumazet [Thu, 23 May 2013 07:44:20 +0000 (07:44 +0000)]
tcp: xps: fix reordering issues

commit 3853b5841c01a ("xps: Improvements in TX queue selection")
introduced ooo_okay flag, but the condition to set it is slightly wrong.

In our traces, we have seen ACK packets being received out of order,
and RST packets sent in response.

We should test if we have any packets still in host queue.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMerge tag 'gpio-fixes-v3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linus...
Linus Torvalds [Fri, 24 May 2013 01:24:10 +0000 (18:24 -0700)]
Merge tag 'gpio-fixes-v3.10-1' of git://git./linux/kernel/git/linusw/linux-gpio

Pull GPIO fixes from Linus Walleij:
 - An OMAP fix that makes ethernet work again.
 - Fix for build problem when building the MCP23S08 driver as module.
 - IRQ conflicts in the Langwell driver.
 - Fix IRQ coherency issues in the MXS driver.
 - Return correct errorcode on errorpath when removing GPIO chips.

* tag 'gpio-fixes-v3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: Don't override the error code in probe error handling
  gpio: mxs: Use set and clear capabilities of the gpio controller
  gpio-langwell: fix irq conflicts when DT is not used
  gpio: mcp23s08: Fix build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m
  gpio/omap: ensure gpio context is initialised

12 years agoMerge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel...
Dave Airlie [Fri, 24 May 2013 00:15:12 +0000 (10:15 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-next

Daniel writes:
A few fixes, nothing shocking:
- More Haswell pci ids. Includes a pile of marketing spare ids (which
  despite the spare moniker show up all over the place).
- Fix a regression in handling modeset failures, resulting in black
  screens on 3 pipe setups when we've run out of pch plls (Chris).
- Fix up the setcrtc semantics to unconditionally enable the outputs.
  Juding from git digging that has (kinda) always been the case and neatly
  fixes a few long-standing (i.e. forever) bug reports (Imre).
- jiffies_timeout + 1 patches from Imre. They partially fix spurious
  wait_event failures in the interrupt-driven dp aux/i2c code. The other
  part is a core patch for the wait_event macros going in through -mm. A
  few patches more than strictly required since Imre is pushing for a
  general solution in 3.11.

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: avoid premature DP AUX timeouts
  drm/i915: avoid premature timeouts in __wait_seqno()
  drm/i915: use msecs_to_jiffies_timeout instead of open coding the same
  drm/i915: add msecs_to_jiffies_timeout to guarantee minimum duration
  drm/i915: force full modeset if the connector is in DPMS OFF mode
  drm/i915: Propagate errors back from fb set-base
  drm/i915: Adding more reserved PCI IDs for Haswell.

12 years agoMerge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git...
Dave Airlie [Fri, 24 May 2013 00:14:57 +0000 (10:14 +1000)]
Merge branch 'exynos-drm-fixes' of git://git./linux/kernel/git/daeinki/drm-exynos into drm-next

Inki writes:
  This pull request includes drm_send_vblank_event() helper
   relevant patch I missed and code cleanups. And also it fixes
   a pended page flip issue.

* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos: replace request_threaded_irq with devm function
  drm/exynos: remove unnecessary devm_kfree
  drm/exynos: fix build warnings from ipp fimc
  drm/exynos: cleanup device pointer usages
  drm/exynos: wait for the completion of pending page flip
  drm/exynos: use drm_send_vblank_event() helper
  drm/exynos: page flip fixes
  drm/exynos: exynos_hdmi: Pass correct pointer to free_irq()
  drm/exynos: exynos_drm_ipp: Fix incorrect usage of IS_ERR_OR_NULL
  drm/exynos: exynos_drm_fbdev: Fix incorrect usage of IS_ERR_OR_NULL

Conflicts:
drivers/gpu/drm/exynos/exynos_hdmi.c

12 years agoMerge remote-tracking branch 'pfdo/drm-fixes' into drm-next
Dave Airlie [Fri, 24 May 2013 00:12:22 +0000 (10:12 +1000)]
Merge remote-tracking branch 'pfdo/drm-fixes' into drm-next

Pull the vblank event changes into a Linus master tree to make merging
easier.

12 years agoNFS: Fix SETCLIENTID fallback if GSS is not available
Chuck Lever [Thu, 16 May 2013 02:00:10 +0000 (22:00 -0400)]
NFS: Fix SETCLIENTID fallback if GSS is not available

Commit 79d852bf "NFS: Retry SETCLIENTID with AUTH_SYS instead of
AUTH_NONE" did not take into account commit 23631227 "NFSv4: Fix the
fallback to AUTH_NULL if krb5i is not available".

Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
12 years agoMerge tag 'pci-v3.10-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaa...
Linus Torvalds [Thu, 23 May 2013 20:50:53 +0000 (13:50 -0700)]
Merge tag 'pci-v3.10-fixes-2' of git://git./linux/kernel/git/helgaas/pci

Pull PCI updates from Bjorn Helgaas:
 "Here are some more fixes for v3.10.  The Moorestown update broke Intel
  Medfield devices, so I reverted it.  The acpiphp change fixes a
  regression: we broke hotplug notifications to host bridges when we
  split acpiphp into the host-bridge related part and the
  endpoint-related part.

  Moorestown
      Revert "x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0"
  Hotplug
      PCI: acpiphp: Re-enumerate devices when host bridge receives Bus Check"

* tag 'pci-v3.10-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  Revert "x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0"
  PCI: acpiphp: Re-enumerate devices when host bridge receives Bus Check

12 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Linus Torvalds [Thu, 23 May 2013 20:50:03 +0000 (13:50 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:
 "A few fixups to Wacom and eGalax touchscreen driver"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: wacom - add an eraser to DTH2242/DTK2241
  Input: wacom - add a few new styli for Cintiq series
  Input: wacom - add three new display tablets
  Input: egalax_ts - ABS_MT_POSITION_Y not reported well

12 years agocfg80211: fix reporting 64-bit station info tx bytes
Felix Fietkau [Thu, 23 May 2013 13:05:59 +0000 (15:05 +0200)]
cfg80211: fix reporting 64-bit station info tx bytes

Copy & paste mistake - STATION_INFO_TX_BYTES64 is the name of the flag,
not NL80211_STA_INFO_TX_BYTES64.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agonet: Revert unused variable changes.
David S. Miller [Thu, 23 May 2013 19:15:32 +0000 (12:15 -0700)]
net: Revert unused variable changes.

This reverts commits:

c573972c111eb4c6b3f3250ad71e7c75cc799833
1a5904342c7380ceddd61c0b37544d752d0b1433
da2e2c214953f37c2a6be20226537ca5a329724c

They were meant for net-next not net.

Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agomac80211: fix queue handling crash
Johannes Berg [Thu, 23 May 2013 19:04:38 +0000 (21:04 +0200)]
mac80211: fix queue handling crash

The code I added in "mac80211: don't start new netdev queues
if driver stopped" crashes for monitor and AP VLAN interfaces
because while they have a netdev, they don't have queues set
up by the driver.

To fix the crash, exclude these from queue accounting here
and just start their netdev queues unconditionally.

For monitor, this is the best we can do, as we can redirect
frames there to any other interface and don't know which one
that will since it can be different for each frame.

For AP VLAN interfaces, we can do better later and actually
properly track the queue status. Not doing this is really a
separate bug though.

Reported-by: Ilan Peer <ilan.peer@intel.com>
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agoReturn the result from user admin command IOCTL even in case of failure
Chayan Biswas [Wed, 22 May 2013 22:34:49 +0000 (22:34 +0000)]
Return the result from user admin command IOCTL even in case of failure

We copy the result to user if the command is completed from the
controller even if it completes with failure (non-zero) status.
A return status of < 0 indicates the command was not completed
by the controller. The user application may expect the error code
in the result field in case of failure.

Signed-off-by: Chayan Biswas <Chayan.Biswas@sandisk.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
12 years agoMerge tag 'tty-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Linus Torvalds [Thu, 23 May 2013 16:28:34 +0000 (09:28 -0700)]
Merge tag 'tty-3.10-rc2' of git://git./linux/kernel/git/gregkh/tty

Pull tty/serial fixes from Greg Kroah-Hartman:
 "Here are some tty / serial driver fixes for 3.10-rc2.

  Nothing huge, although the rocket driver fix looks large, it's just
  moving the code around to fix the reported build issues in it.  Other
  than that, this has the fix for the of-reported lockdep warning from
  the vt layer, as well as some other needed bugfixes.

  All of these have been in linux-next for a while"

* tag 'tty-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: mxser: Fix build warning introduced by dfc7b837c7f9 (Re: linux-next: build warning after merge of the tty.current tree)
  tty: mxser: fix usage of opmode_ioaddr
  serial: 8250_dw: add ACPI ID for Intel BayTrail
  TTY: Fix tty miss restart after we turn off flow-control
  tty/vt: Fix vc_deallocate() lock order
  TTY: ehv_bytechan: add missing platform_driver_unregister() when module exit
  TTY: rocket, fix more no-PCI warnings
  serial: mcf: missing uart_unregister_driver() on error in mcf_init()
  tty: serial: mpc5xxx: fix error handing in mpc52xx_uart_init()
  serial: samsung: add missing platform_driver_unregister() when module exit
  serial: pl011: protect attribute read from NULL platform data struct
  tty: nwpserial: Pass correct pointer to free_irq()
  serial: 8250_dw: Add valid clk pointer check

12 years agoMerge tag 'staging-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh...
Linus Torvalds [Thu, 23 May 2013 16:27:49 +0000 (09:27 -0700)]
Merge tag 'staging-3.10-rc2' of git://git./linux/kernel/git/gregkh/staging

Pull staging driver fixes from Greg Kroah-Hartman:
 "Here are some staging tree driver fixes for 3.10-rc2

  The drivers/iio/ changes are here as they are still tied into
  drivers/staging/iio/.

  Nothing major, just a number of small bugfixes, and a larger
  documentation update for the ramster code."

* tag 'staging-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
  staging: dwc2: remove compile warning for USB_DWC2_TRACK_MISSED_SOFS
  iio: exynos_adc: fix wrong structure extration in suspend and resume
  iio:common:st: added disable function after read info raw data
  iio: dac: Fix build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m
  staging:iio:light:tsl2x7x: fix the error handling in tsl2x7x_probe()
  staging/iio/mxs-lradc: fix preenable for multiple buffers
  staging: imx-drm: imx-tve: Check the return value of 'regulator_enable()'
  staging: video: imx: Select VIDEOMODE_HELPERS for parallel display
  staging: ramster: add how-to document
  staging: dwc2: Fix dma-enabled platform devices using a default dma_mask
  staging: vt6656: [bug] Fix missing spin lock in iwctl_siwpower.
  staging: Swap zram and zsmalloc in Kconfig
  staging: android: logger: use kuid_t instead of uid_t
  staging: zcache: Fix incorrect module_param_array types
  staging/solo6x10: depend on CONFIG_FONTS
  staging/drm: imx: add missing dependencies
  staging: ste_rmi4: Suppress 'ignoring return value of ‘regulator_enable()' warning
  staging: sep: fix driver build and kconfig
  staging: nvec: cleanup childs on remove
  staging: nvec: implement unregistering of notifiers
  ...

12 years agoMerge tag 'driver-core-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Thu, 23 May 2013 16:27:08 +0000 (09:27 -0700)]
Merge tag 'driver-core-3.10-rc2' of git://git./linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg Kroah-Hartman:
 "Here are 3 tiny driver core fixes for 3.10-rc2.

  A needed symbol export, a change to make it easier to track down
  offending sysfs files with incorrect attributes, and a klist bugfix.

  All have been in linux-next for a while"

* tag 'driver-core-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  klist: del waiter from klist_remove_waiters before wakeup waitting process
  driver core: print sysfs attribute name when warning about bogus permissions
  driver core: export subsys_virtual_register

12 years agoMerge tag 'char-misc-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregk...
Linus Torvalds [Thu, 23 May 2013 16:26:32 +0000 (09:26 -0700)]
Merge tag 'char-misc-3.10-rc2' of git://git./linux/kernel/git/gregkh/char-misc

Pull char/misc driver fixes from Greg Kroah-Hartman:
 "Here are some small char/misc driver fixes for 3.10-rc2.

  Nothing major here, just a number of fixes for things that people have
  reported, and a MAINTAINERS update for the recent changes for the
  hyperv files that went into 3.10-rc1."

* tag 'char-misc-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  ttyprintk: Fix NULL pointer deref by setting tty_port ops after initializing port
  uio: UIO_DMEM_GENIRQ should depend on HAS_DMA
  MAINTAINERS: update Hyper-V file list
  mei: bus: Reset event_cb when disabling a device
  Drivers: hv: Fix a bug in get_vp_index()
  mei: fix out of array access to me clients array
  Char: lp, protect LPGETSTATUS with port_mutex
  dummy-irq: require the user to specify an IRQ number

12 years agoMerge tag 'usb-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Linus Torvalds [Thu, 23 May 2013 16:23:32 +0000 (09:23 -0700)]
Merge tag 'usb-3.10-rc2' of git://git./linux/kernel/git/gregkh/usb

Pull USB fixes from Greg Kroah-Hartman:
 "Here are a number of tiny USB bugfixes / new device ids for 3.10-rc2

  The majority of these are USB gadget fixes, but they are all small.
  Other than that, some USB host controller fixes, and USB serial driver
  fixes for problems reported with them.

  Also hopefully a fixed up USB_OTG Kconfig dependancy, that one seems
  to be almost impossible to get right for all of the different
  platforms these days."

* tag 'usb-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (56 commits)
  USB: cxacru: potential underflow in cxacru_cm_get_array()
  USB: ftdi_sio: Add support for Newport CONEX motor drivers
  USB: option: add device IDs for Dell 5804 (Novatel E371) WWAN card
  usb: ohci: fix goto wrong tag in err case
  usb: isp1760-if: fix memleak when platform_get_resource fail
  usb: ehci-s5p: fix memleak when fallback to pdata
  USB: serial: clean up chars_in_buffer
  USB: ti_usb_3410_5052: fix chars_in_buffer overhead
  USB: io_ti: fix chars_in_buffer overhead
  USB: ftdi_sio: fix chars_in_buffer overhead
  USB: ftdi_sio: clean up get_modem_status
  USB: serial: add generic wait_until_sent implementation
  USB: serial: add wait_until_sent operation
  USB: set device dma_mask without reference to global data
  USB: Blacklisted Cinterion's PLxx WWAN Interface
  usb: option: Add Telewell TW-LTE 4G
  USB: EHCI: remove bogus #error
  USB: reset resume quirk needed by a hub
  USB: usb-stor: realtek_cr: Fix compile error
  usb, chipidea: fix link error when USB_EHCI_HCD is a module
  ...

12 years agoMerge git://git.kernel.org/pub/scm/virt/kvm/kvm
Linus Torvalds [Thu, 23 May 2013 16:18:08 +0000 (09:18 -0700)]
Merge git://git.kernel.org/pub/scm/virt/kvm/kvm

Pull kvm bugfixes from Gleb Natapov.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM/MIPS32: Wrap calls to gfn_to_pfn() with srcu_read_lock/unlock()
  KVM/MIPS32: Move include/asm/kvm.h => include/uapi/asm/kvm.h since it is a user visible API.
  KVM: take over co-maintainership from Marcelo, fix MAINTAINERS entry

12 years agolib: make iovec obj instead of lib
Randy Dunlap [Thu, 23 May 2013 05:46:09 +0000 (22:46 -0700)]
lib: make iovec obj instead of lib

Fix build error io vmw_vmci.ko when CONFIG_VMWARE_VMCI=m by chaning
iovec.o from lib-y to obj-y.

  ERROR: "memcpy_toiovec" [drivers/misc/vmw_vmci/vmw_vmci.ko] undefined!
  ERROR: "memcpy_fromiovec" [drivers/misc/vmw_vmci/vmw_vmci.ko] undefined!

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
12 years agocfg80211: check wdev->netdev in connection work
Johannes Berg [Thu, 23 May 2013 16:10:21 +0000 (18:10 +0200)]
cfg80211: check wdev->netdev in connection work

If a P2P-Device is present and another virtual interface triggers
the connection work, the system crash because it tries to check
if the P2P-Device's netdev (which doesn't exist) is up. Skip any
wdevs that have no netdev to fix this.

Cc: stable@vger.kernel.org
Reported-by: YanBo <dreamfly281@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agoregmap: regcache: Fixup locking for custom lock callbacks
Lars-Peter Clausen [Thu, 23 May 2013 15:23:49 +0000 (17:23 +0200)]
regmap: regcache: Fixup locking for custom lock callbacks

The parameter passed to the regmap lock/unlock callbacks needs to be
map->lock_arg, regcache passes just map. This works fine in the case that no
custom locking callbacks are used since in this case map->lock_arg equals map,
but will break when custom locking callbacks are used. The issue was introduced
in commit 0d4529c5("regmap: make lock/unlock functions customizable") and is
fixed by this patch.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
12 years agoInput: wacom - add an eraser to DTH2242/DTK2241
Ping Cheng [Wed, 15 May 2013 06:34:53 +0000 (23:34 -0700)]
Input: wacom - add an eraser to DTH2242/DTK2241

plus send begin and end of express keys events for
Cintiq 13HD and DTH2242/DTK2241

Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
12 years agotracing: Fix crash when ftrace=nop on the kernel command line
Steven Rostedt (Red Hat) [Thu, 23 May 2013 15:51:10 +0000 (11:51 -0400)]
tracing: Fix crash when ftrace=nop on the kernel command line

If ftrace=<tracer> is on the kernel command line, when that tracer is
registered, it will be initiated by tracing_set_tracer() to execute that
tracer.

The nop tracer is just a stub tracer that is used to have no tracer
enabled. It is assigned at early bootup as it is the default tracer.

But if ftrace=nop is on the kernel command line, the registering of the
nop tracer will call tracing_set_tracer() which will try to execute
the nop tracer. But it expects tr->current_trace to be assigned something
as it usually is assigned to the nop tracer. As it hasn't been assigned
to anything yet, it causes the system to crash.

The simple fix is to move the tr->current_trace = nop before registering
the nop tracer. The functionality is still the same as the nop tracer
doesn't do anything anyway.

Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
12 years agoMIPS: Trap exception handling fixes
Maciej W. Rozycki [Thu, 23 May 2013 14:31:23 +0000 (14:31 +0000)]
MIPS: Trap exception handling fixes

2a0b24f56c2492b932f1aed617ae80fb23500d21 broke Trap exception handling in
the standard MIPS mode.  Additionally the microMIPS-mode trap code mask is
wrong, as it's a 4-bit field.  Here's a fix.

Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5309/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
12 years agoALSA: usb-6fire: Modify firmware version check
Torsten Schenk [Thu, 23 May 2013 11:38:29 +0000 (13:38 +0200)]
ALSA: usb-6fire: Modify firmware version check

Check only the uppermost 16 bits instead of the whole 32 bits of
the version information. Do this because all firmware version tested
with this version information worked correctly and the strict check
causes problems for several users.

Signed-off-by: Torsten Schenk <torsten.schenk@zoho.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
12 years agonetfilter: ipt_ULOG: fix non-null terminated string in the nf_log path
Chen Gang [Thu, 23 May 2013 01:50:46 +0000 (01:50 +0000)]
netfilter: ipt_ULOG: fix non-null terminated string in the nf_log path

If nf_log uses ipt_ULOG as logging output, we can deliver non-null
terminated strings to user-space since the maximum length of the
prefix that is passed by nf_log is NF_LOG_PREFIXLEN but pm->prefix
is 32 bytes long (ULOG_PREFIX_LEN).

This is actually happening already from nf_conntrack_tcp if ipt_ULOG
is used, since it is passing strings longer than 32 bytes.

Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
12 years agodrm/exynos: replace request_threaded_irq with devm function
Seung-Woo Kim [Wed, 22 May 2013 12:14:17 +0000 (21:14 +0900)]
drm/exynos: replace request_threaded_irq with devm function

devm_request_threaded_irq is used instead of request_threaded_irq
and free_irq is removed.

Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
12 years agodrm/exynos: remove unnecessary devm_kfree
Seung-Woo Kim [Wed, 22 May 2013 12:14:16 +0000 (21:14 +0900)]
drm/exynos: remove unnecessary devm_kfree

devm_kfree does not need for fail case of probe function and for
remove function.

Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
12 years agodrm/exynos: fix build warnings from ipp fimc
Seung-Woo Kim [Wed, 22 May 2013 12:14:15 +0000 (21:14 +0900)]
drm/exynos: fix build warnings from ipp fimc

Becuase of order of headers, there are build warnings and they are
fixed with this patch.

Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
12 years agodrm/exynos: cleanup device pointer usages
Seung-Woo Kim [Wed, 22 May 2013 12:14:14 +0000 (21:14 +0900)]
drm/exynos: cleanup device pointer usages

Struct device pointer got from platform device pointer is already
alsigned as variable, but some functions do not use device pointer.
So this patch replaces thoes usages.

Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
12 years agodrm/exynos: wait for the completion of pending page flip
Inki Dae [Tue, 21 May 2013 07:55:58 +0000 (16:55 +0900)]
drm/exynos: wait for the completion of pending page flip

This patch fixes the issue that drm_vblank_get() is failed.

The issus occurs when next page flip request is tried
if previous page flip event wasn't completed yet and then
dpms became off.

So this patch make sure that page flip event is completed
before dpms goes to off.

Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
12 years agodrm/exynos: use drm_send_vblank_event() helper
Rob Clark [Wed, 22 May 2013 02:48:40 +0000 (11:48 +0900)]
drm/exynos: use drm_send_vblank_event() helper

Rebased.

Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
12 years agonetfilter: add nf_ipv6_ops hook to fix xt_addrtype with IPv6
Florian Westphal [Fri, 17 May 2013 03:56:10 +0000 (03:56 +0000)]
netfilter: add nf_ipv6_ops hook to fix xt_addrtype with IPv6

Quoting https://bugzilla.netfilter.org/show_bug.cgi?id=812:

[ ip6tables -m addrtype ]
When I tried to use in the nat/PREROUTING it messes up the
routing cache even if the rule didn't matched at all.
[..]
If I remove the --limit-iface-in from the non-working scenario, so just
use the -m addrtype --dst-type LOCAL it works!

This happens when LOCAL type matching is requested with --limit-iface-in,
and the default ipv6 route is via the interface the packet we test
arrived on.

Because xt_addrtype uses ip6_route_output, the ipv6 routing implementation
creates an unwanted cached entry, and the packet won't make it to the
real/expected destination.

Silently ignoring --limit-iface-in makes the routing work but it breaks
rule matching (--dst-type LOCAL with limit-iface-in is supposed to only
match if the dst address is configured on the incoming interface;
without --limit-iface-in it will match if the address is reachable
via lo).

The test should call ipv6_chk_addr() instead.  However, this would add
a link-time dependency on ipv6.

There are two possible solutions:

1) Revert the commit that moved ipt_addrtype to xt_addrtype,
   and put ipv6 specific code into ip6t_addrtype.
2) add new "nf_ipv6_ops" struct to register pointers to ipv6 functions.

While the former might seem preferable, Pablo pointed out that there
are more xt modules with link-time dependeny issues regarding ipv6,
so lets go for 2).

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
12 years agoOMAPDSS: Fix crash with DT boot
Tomi Valkeinen [Thu, 23 May 2013 09:07:50 +0000 (12:07 +0300)]
OMAPDSS: Fix crash with DT boot

When booting with DT, there's a crash when omapfb is probed. This is
caused by the fact that omapdss+DT is not yet supported, and thus
omapdss is not probed at all. On the other hand, omapfb is always
probed. When omapfb tries to use omapdss, there's a NULL pointer
dereference crash. The same error should most likely happen with omapdrm
and omap_vout also.

To fix this, add an "initialized" state to omapdss. When omapdss has
been probed, it's marked as initialized. omapfb, omapdrm and omap_vout
check this state when they are probed to see that omapdss is actually
there.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
12 years agoARC: Use enough bits for determining page's cache color
Vineet Gupta [Sun, 19 May 2013 08:36:44 +0000 (14:06 +0530)]
ARC: Use enough bits for determining page's cache color

The current code uses 2 bits for determining page's dcache color, thus
sorting pages into 4 bins, whereas the aliasing dcache really has 2 bins
(8k page, 64k dcache - 4 way-set-assoc).
This can cause extraneous flushes - e.g. color 0 and 2.

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
12 years agoARC: Brown paper bag bug in macro for checking cache color
Vineet Gupta [Wed, 22 May 2013 13:08:10 +0000 (18:38 +0530)]
ARC: Brown paper bag bug in macro for checking cache color

The VM_EXEC check in update_mmu_cache() was getting optimized away
because of a stupid error in definition of macro addr_not_cache_congruent()

The intention was to have the equivalent of following:

if (a || (1 ? b : 0))

but we ended up with following:

if (a || 1 ? b : 0)

And because precedence of '||' is more that that of '?', gcc was optimizing
away evaluation of <a>

Nasty Repercussions:
1. For non-aliasing configs it would mean some extraneous dcache flushes
   for non-code pages if U/K mappings were not congruent.
2. For aliasing config, some needed dcache flush for code pages might
   be missed if U/K mappings were congruent.

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
12 years agoMerge branch 'pm-cpufreq'
Rafael J. Wysocki [Thu, 23 May 2013 08:33:52 +0000 (10:33 +0200)]
Merge branch 'pm-cpufreq'

* pm-cpufreq:
  cpufreq: arm_big_little_dt: Instantiate as platform_driver
  cpufreq: arm_big_little_dt: Register driver only if DT has valid data
  cpufreq / e_powersaver: Fix linker error when ACPI processor is a module
  cpufreq / intel_pstate: Add additional supported CPU ID
  cpufreq: Drop rwsem lock around CPUFREQ_GOV_POLICY_EXIT

12 years agoMerge branch 'acpi-fixes'
Rafael J. Wysocki [Thu, 23 May 2013 08:33:44 +0000 (10:33 +0200)]
Merge branch 'acpi-fixes'

* acpi-fixes:
  ACPI / video: Add "Asus UL30A" to ACPI video detect blacklist
  ACPI / PM: Allow device power states to be used for CONFIG_PM unset

12 years agoxfrm: properly handle invalid states as an error
Timo Teräs [Wed, 22 May 2013 01:40:47 +0000 (01:40 +0000)]
xfrm: properly handle invalid states as an error

The error exit path needs err explicitly set. Otherwise it
returns success and the only caller, xfrm_output_resume(),
would oops in skb_dst(skb)->ops derefence as skb_dst(skb) is
NULL.

Bug introduced in commit bb65a9cb (xfrm: removes a superfluous
check and add a statistic).

Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Cc: Li RongQing <roy.qing.li@gmail.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMIPS: Quit exposing Kconfig symbols in uapi headers.
David Daney [Wed, 22 May 2013 22:35:56 +0000 (22:35 +0000)]
MIPS: Quit exposing Kconfig symbols in uapi headers.

The kernel's struct pt_regs has many fields conditional on various
Kconfig variables, we cannot be exporting this garbage to user-space.

Move the kernel's definition to asm/ptrace.h, and put a uapi only
version in uapi/asm/ptrace.h gated by #ifndef __KERNEL__

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5305/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
12 years agoMIPS: Remove duplicate definition of check_for_high_segbits.
David Daney [Wed, 22 May 2013 21:27:22 +0000 (21:27 +0000)]
MIPS: Remove duplicate definition of check_for_high_segbits.

In C, one definition is sufficient.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5304/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
12 years agokbuild: Don't assume dts files live in arch/*/boot/dts
Matthijs Kooijman [Wed, 8 May 2013 10:59:04 +0000 (12:59 +0200)]
kbuild: Don't assume dts files live in arch/*/boot/dts

In commit b40b25ff (kbuild: always run gcc -E on *.dts, remove cmd_dtc_cpp),
dts building was changed to always use the C preprocessor. This meant
that the .dts file passed to dtc is not the original, but the
preprocessed one.

When compiling with a separate build directory (i.e., with O=), this
preprocessed file will not live in the same directory as the original.
When the .dts file includes .dtsi files, dtc will look for them in the
build directory, not in the source directory and compilation will fail.

The commit referenced above tried to fix this by passing arch/*/boot/dts
as an include path to dtc. However, for mips, the .dts files are not in
this directory, so dts compilation on mips breaks for some targets.

Instead of hardcoding this particular include path, this commit just
uses the directory of the .dts file that is being compiled, which
effectively restores the previous behaviour wrt includes. For most .dts
files, this path is just the same as the previous hardcoded
arch/*/boot/dts path.

This was tested on a mips (rt3052) and an arm (bcm2835) target.

Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
12 years agovirtio_net: enable napi for all possible queues during open
Jason Wang [Tue, 21 May 2013 20:03:58 +0000 (20:03 +0000)]
virtio_net: enable napi for all possible queues during open

Commit 55257d72bd1c51f25106350f4983ec19f62ed1fa (virtio-net: fill only rx
queues which are being used) only does the napi enabling during open for
curr_queue_pairs. This will break multiqueue receiving since napi of new queues
were still disabled after changing the number of queues.

This patch fixes this by enabling napi for all possible queues during open.

Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agotcp: bug fix in proportional rate reduction.
Nandita Dukkipati [Tue, 21 May 2013 15:12:07 +0000 (15:12 +0000)]
tcp: bug fix in proportional rate reduction.

This patch is a fix for a bug triggering newly_acked_sacked < 0
in tcp_ack(.).

The bug is triggered by sacked_out decreasing relative to prior_sacked,
but packets_out remaining the same as pior_packets. This is because the
snapshot of prior_packets is taken after tcp_sacktag_write_queue() while
prior_sacked is captured before tcp_sacktag_write_queue(). The problem
is: tcp_sacktag_write_queue (tcp_match_skb_to_sack() -> tcp_fragment)
adjusts the pcount for packets_out and sacked_out (MSS change or other
reason). As a result, this delta in pcount is reflected in
(prior_sacked - sacked_out) but not in (prior_packets - packets_out).

This patch does the following:
1) initializes prior_packets at the start of tcp_ack() so as to
capture the delta in packets_out created by tcp_fragment.
2) introduces a new "previous_packets_out" variable that snapshots
packets_out right before tcp_clean_rtx_queue, so pkts_acked can be
correctly computed as before.
3) Computes pkts_acked using previous_packets_out, and computes
newly_acked_sacked using prior_packets.

Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMerge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
David S. Miller [Thu, 23 May 2013 07:08:36 +0000 (00:08 -0700)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge

Included change:
- fix double free in case of failure during mesh initialisation

Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agomicroblaze: Use proper casting for inb/inw/inl in io.h
Michal Simek [Thu, 23 May 2013 06:04:09 +0000 (08:04 +0200)]
microblaze: Use proper casting for inb/inw/inl in io.h

We are going to move to asm-generic/io.h but
let's fix compilation warnings first for 3.10.

Warning message:
arch/microblaze/include/asm/io.h:126:26: warning: cast to
 pointer from integer of different size [-Wint-to-pointer-cast]
 #define inb(port)  readb((u8 *)((port)))
...

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
12 years agonet: ethernet: sun: drop unused variable
Emilio López [Wed, 22 May 2013 13:57:37 +0000 (13:57 +0000)]
net: ethernet: sun: drop unused variable

Commit bfd428d ("net: ethernet: sun: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agonet: ethernet: korina: drop unused variable
Emilio López [Wed, 22 May 2013 13:57:36 +0000 (13:57 +0000)]
net: ethernet: korina: drop unused variable

Commit e998fd4 ("net: ethernet: korina: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.

Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agonet: ethernet: apple: drop unused variable
Emilio López [Wed, 22 May 2013 13:57:35 +0000 (13:57 +0000)]
net: ethernet: apple: drop unused variable

Commit 3b0aaef ("net: ethernet: apple: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.

Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoARC: copy_(to|from)_user() to honor usermode-access permissions
Vineet Gupta [Tue, 21 May 2013 09:55:11 +0000 (15:25 +0530)]
ARC: copy_(to|from)_user() to honor usermode-access permissions

This manifested as grep failing psuedo-randomly:

-------------->8---------------------
[ARCLinux]$ ip address show lo | grep inet
[ARCLinux]$ ip address show lo | grep inet
[ARCLinux]$ ip address show lo | grep inet
[ARCLinux]$
[ARCLinux]$ ip address show lo | grep inet
    inet 127.0.0.1/8 scope host lo
-------------->8---------------------

ARC700 MMU provides fully orthogonal permission bits per page:
Ur, Uw, Ux, Kr, Kw, Kx

The user mode page permission templates used to have all Kernel mode
access bits enabled.
This caused a tricky race condition observed with uClibc buffered file
read and UNIX pipes.

1. Read access to an anon mapped page in libc .bss: write-protected
   zero_page mapped: TLB Entry installed with Ur + K[rwx]

2. grep calls libc:getc() -> buffered read layer calls read(2) with the
   internal read buffer in same .bss page.
   The read() call is on STDIN which has been redirected to a pipe.
   read(2) => sys_read() => pipe_read() => copy_to_user()

3. Since page has Kernel-write permission (despite being user-mode
   write-protected), copy_to_user() suceeds w/o taking a MMU TLB-Miss
   Exception (page-fault for ARC). core-MM is unaware that kernel
   erroneously wrote to the reserved read-only zero-page (BUG #1)

4. Control returns to userspace which now does a write to same .bss page
   Since Linux MM is not aware that page has been modified by kernel, it
   simply reassigns a new writable zero-init page to mapping, loosing the
   prior write by kernel - effectively zero'ing out the libc read buffer
   under the hood - hence grep doesn't see right data (BUG #2)

The fix is to make all kernel-mode access permissions mirror the
user-mode ones. Note that the kernel still has full access to pages,
when accessed directly (w/o MMU) - this fix ensures that kernel-mode
access in copy_to_from() path uses the same faulting access model as for
pure user accesses to keep MM fully aware of page state.

The issue is peudo-random because it only shows up if the TLB entry
installed in #1 is present at the time of #3. If it is evicted out, due
to TLB pressure or some-such, then copy_to_user() does take a TLB Miss
Exception, with a routine write-to-anon COW processing installing a
fresh page for kernel writes and also usable as it is in userspace.

Further the issue was dormant for so long as it depends on where the
libc internal read buffer (in .bss) is mapped at runtime.
If it happens to reside in file-backed data mapping of libc (in the
page-aligned slack space trailing the file backed data), loader zero
padding the slack space, does the early cow page replacement, setting
things up at the very beginning itself.

With gcc 4.8 based builds, the libc buffer got pushed out to a real
anon mapping which triggers the issue.

Reported-by: Anton Kolesov <akolesov@synopsys.com>
Cc: <stable@vger.kernel.org> # 3.9
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
12 years agoARC: [mm] Prevent stray dcache lines after__sync_icache_dcach()
Vineet Gupta [Thu, 16 May 2013 06:49:29 +0000 (12:19 +0530)]
ARC: [mm] Prevent stray dcache lines after__sync_icache_dcach()

Flush and INVALIDATE the dcache page.

This helper is only used for writeback of CODE pages to memory. So
there's no value in keeping the dcache lines around. Infact it is risky
as a writeback on natural eviction under pressure can cause un-needed
writeback with weird issues on aliasing dcache configurations.

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
12 years agoARM i.MX6q: fix for ldb_di_sels
Jiada Wang [Mon, 20 May 2013 12:51:51 +0000 (21:51 +0900)]
ARM i.MX6q: fix for ldb_di_sels

As pll5_video_div has been introduced to represent the clock
generated from post-divider for video.
Instead of pll5_video, pll5_video_div should be proper root clock
for ldb_di_sel.

Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
12 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt...
Linus Torvalds [Thu, 23 May 2013 01:06:57 +0000 (18:06 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/egtvedt/linux-avr32

Pull AVR32 update from Hans-Christian Egtvedt:
 "wow, it has gone 10 releases since my last request :("

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
  avr32: fix building warnings caused by redefinitions of HZ
  avr32: fix relocation check for signed 18-bit offset
  avr32: move NODES_SHIFT into Kconfig and delete numnodes.h

12 years agoMerge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Linus Torvalds [Thu, 23 May 2013 01:05:45 +0000 (18:05 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus

Pull MIPS update from Ralf Baechle:
 - Fix a build error if <linux/printk.h> is included without
   <linux/linkage.h> having been included before.
 - Cleanup and fix the damage done by the generic idle loop patch.
 - A kprobes fix that brings the MIPS code in line with what other
   architectures are for quite a while already.
 - Wire up the native getdents64(2) syscall for 64 bit - for some reason
   it was only for the compat ABIs.  This has been reported to cause an
   application issue.  This turned out bigger than I meant but the wait
   instruction support code was driving me nuts.

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: N64: Wire getdents64(2)
  kprobes/mips: Fix to check double free of insn slot
  MIPS: Idle: Break r4k_wait into two functions and fix it.
  MIPS: Idle: Do address fiddlery in helper functions.
  MIPS: Idle: Consolidate all declarations in <asm/idle.h>.
  MIPS: Idle: Don't call local_irq_disable() in cpu_wait() implementations.
  MIPS: Idle: Re-enable irqs at the end of r3081, au1k and loongson2 cpu_wait.
  MIPS: Idle: Make call of function pointer readable.
  MIPS: Idle: Consistently reformat inline assembler.
  MIPS: Idle: cleaup SMTC idle hook as per Linux coding style.
  MIPS: Consolidate idle loop / WAIT instruction support in a single file.
  MIPS: clock.h: Remove declaration of cpu_wait.
  Add include dependencies to <linux/printk.h>.
  MIPS: Rewrite pfn_valid to work in modules, too.

12 years agoACPI / video: Add "Asus UL30A" to ACPI video detect blacklist
Bastian Triller [Sun, 19 May 2013 11:52:33 +0000 (11:52 +0000)]
ACPI / video: Add "Asus UL30A" to ACPI video detect blacklist

Like on UL30VT, the ACPI video driver can't control backlight correctly on
Asus UL30A.  Vendor driver (asus-laptop) can work.  This patch is to
add "Asus UL30A" to ACPI video detect blacklist in order to use
asus-laptop for video control on the "Asus UL30A" rather than ACPI
video driver.

Signed-off-by: Bastian Triller <bastian.triller@gmail.com>
Cc: All <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
12 years agostaging: dwc2: remove compile warning for USB_DWC2_TRACK_MISSED_SOFS
Paul Zimmerman [Wed, 22 May 2013 22:10:15 +0000 (15:10 -0700)]
staging: dwc2: remove compile warning for USB_DWC2_TRACK_MISSED_SOFS

Remove the compile-time warning for this config option, and instead
warn that it is experimental in the Kconfig text

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
12 years agoqmi_wwan: Added support for Cinterion's PLxx WWAN Interface
Hans-Christoph Schemmel [Tue, 21 May 2013 02:07:17 +0000 (02:07 +0000)]
qmi_wwan: Added support for Cinterion's PLxx WWAN Interface

Added support for Cinterion's PLxx WWAN Interface by adding QMI_FIXED_INTF with
Cinterion's Vendor ID as well as Product ID and WWAN Interface Number.

Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
Signed-off-by: Christian Schmiedl <christian.schmiedl@gemalto.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoMerge tag 'iio-fixes-for-3.10a' of git://git.kernel.org/pub/scm/linux/kernel/git...
Greg Kroah-Hartman [Wed, 22 May 2013 22:11:31 +0000 (15:11 -0700)]
Merge tag 'iio-fixes-for-3.10a' of git://git./linux/kernel/git/jic23/iio into staging-linus

Jonathan writes:

First round of IIO fixes for the 3.10 cycle.

The usual mixed bag of little fixes.

1) A fix for mxs-lradc having missed out on some global abi changes that and
   hence being unable to start up buffered output.
2) Clean up error handling in tsl2x7x
3) A build fix for some of the dac drivers when they have spi master support
   built in, but i2c support build as a module.
4) Add a missing disable after a oneshot capture to the st sensor core.
5) Exynos adc driver took a novel an incorrect route to get at its private
   data store.

12 years agoMerge branch 'perf_net_dropmonitor'
David S. Miller [Wed, 22 May 2013 22:10:25 +0000 (15:10 -0700)]
Merge branch 'perf_net_dropmonitor'

Ben Hutchings says:

====================
Somewhat surprisingly, the net_dropmonitor reporting script doesn't work
at all.  This series fixes it and then makes it slightly more efficient.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
12 years agoperf: net_dropmonitor: Remove progress indicator
Ben Hutchings [Mon, 20 May 2013 14:45:57 +0000 (14:45 +0000)]
perf: net_dropmonitor: Remove progress indicator

We can read /proc/kallsyms in a fraction of a second, so why waste
a further fraction of a second showing progress?

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoperf: net_dropmonitor: Use bisection in symbol lookup
Ben Hutchings [Mon, 20 May 2013 14:45:42 +0000 (14:45 +0000)]
perf: net_dropmonitor: Use bisection in symbol lookup

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoperf: net_dropmonitor: Do not assume ordering of dictionaries
Ben Hutchings [Mon, 20 May 2013 14:45:34 +0000 (14:45 +0000)]
perf: net_dropmonitor: Do not assume ordering of dictionaries

The sort order of dictionaries in Python is undocumented.  Use
tuples instead, which are documented to be lexically ordered.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoperf: net_dropmonitor: Fix symbol-relative addresses
Ben Hutchings [Mon, 20 May 2013 14:45:26 +0000 (14:45 +0000)]
perf: net_dropmonitor: Fix symbol-relative addresses

The comparison between traced and symbol addresses is backwards: if
the traced address doesn't exactly match a symbol (which we don't
expect it to), we'll show the next symbol and the offset to it,
whereas we should show the previous symbol and the offset from it.

Cc: stable@vger.kernel.org
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoperf: net_dropmonitor: Fix trace parameter order
Ben Hutchings [Mon, 20 May 2013 14:44:43 +0000 (14:44 +0000)]
perf: net_dropmonitor: Fix trace parameter order

This works much better if we don't treat protocol numbers as addresses.

Cc: stable@vger.kernel.org
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agonet: fec: use a more proper compatible string for MVF type device
Shawn Guo [Sun, 19 May 2013 04:38:46 +0000 (04:38 +0000)]
net: fec: use a more proper compatible string for MVF type device

MVF is a family while MVF600 is a particular SoC in the family.  We
generally prefer to use SoC rather than family name in compatible string
to define a particular type of fec device.  And this is how fec_dt_ids
works for all those IMX fec variants.  Let's change mvf to mvf600 to
have it work in the same way.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoqlcnic: Fix updating netdev->features
Shahed Shaikh [Tue, 21 May 2013 09:27:01 +0000 (09:27 +0000)]
qlcnic: Fix updating netdev->features

o After change in EPORT features of 82xx adapter, netdev->features needs to
  be updated to reflect EPORT feature updates but driver was manipulating
  netdev->features at wrong place.
o This patch uses netdev_update_features() and .ndo_fix_features() to
  update netdev->features properly.

Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoqlcnic: remove netdev->trans_start updates within the driver
Sony Chacko [Tue, 21 May 2013 09:27:00 +0000 (09:27 +0000)]
qlcnic: remove netdev->trans_start updates within the driver

Code is removed because netdev->trans_start updates made by the driver
will be ignored by the kernel.

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoqlcnic: Return proper error codes from probe failure paths
Sony Chacko [Tue, 21 May 2013 09:26:59 +0000 (09:26 +0000)]
qlcnic: Return proper error codes from probe failure paths

Fix error paths in probe to assign proper error codes to probe return value.

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agotg3: Update version to 3.132
Nithin Sujir [Tue, 21 May 2013 12:57:33 +0000 (12:57 +0000)]
tg3: Update version to 3.132

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agotg3: Ensure boot code has completed initialization before accessing hardware
Nithin Sujir [Tue, 21 May 2013 12:57:32 +0000 (12:57 +0000)]
tg3: Ensure boot code has completed initialization before accessing hardware

After resetting the device, the driver waits for a signature to be
updated to know that firmware has completed initialization. However, the
call to tg3_poll_fw() is being done too late and we're writing to the
GRC_MODE register before it has completely initialized, causing
contention with firmware.  This logic has existed since day one but is
causing PCIE link to go down randomly at startup on one platform once
every few hundred reboots.

Move the tg3_poll_fw() up to before we write to the GRC_MODE register
after reset.

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
12 years agoiio: exynos_adc: fix wrong structure extration in suspend and resume
Naveen Krishna Chatradhi [Mon, 20 May 2013 06:34:00 +0000 (07:34 +0100)]
iio: exynos_adc: fix wrong structure extration in suspend and resume

The exynos_adc device structure was wrongly extracted from the dev*
correcting the same.

Using the regular conversion of
struct device* -> struct platform_device* -> struct exynos_adc* seems wrong.
Instead we should be doing
struct device* -> struct iio_dev* -> struct exynos_adc*

Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
12 years agoiio:common:st: added disable function after read info raw data
Denis CIOCCA [Thu, 9 May 2013 13:35:00 +0000 (14:35 +0100)]
iio:common:st: added disable function after read info raw data

Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
12 years agoiio: dac: Fix build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m
Axel Lin [Thu, 9 May 2013 07:49:00 +0000 (08:49 +0100)]
iio: dac: Fix build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m

This patch fixes below build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m:

drivers/built-in.o: In function `ad5064_i2c_write':
drivers/iio/dac/ad5064.c:608: undefined reference to `i2c_master_send'
drivers/built-in.o: In function `ad5064_i2c_register_driver':
drivers/iio/dac/ad5064.c:646: undefined reference to `i2c_register_driver'
drivers/built-in.o: In function `ad5064_i2c_unregister_driver':
drivers/iio/dac/ad5064.c:651: undefined reference to `i2c_del_driver'
make: *** [vmlinux] Error 1

When CONFIG_I2C=m, meaning we can't build the drivers in with I2C support.
Thus don't allow the drivers to be compiled as built-in when CONFIG_I2C=m.

The real fix though is to break the driver apart into a SPI part, an I2C part
and a common part. But that's something for 3.11 while this is something for
3.10/stable.

Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
12 years agostaging:iio:light:tsl2x7x: fix the error handling in tsl2x7x_probe()
Wei Yongjun [Tue, 7 May 2013 11:51:00 +0000 (12:51 +0100)]
staging:iio:light:tsl2x7x: fix the error handling in tsl2x7x_probe()

Fix to return -EINVAL in the i2c device found error handling
case instead of 0, as done elsewhere in this function.
And also correct the fail1 and fail2 lable to do the right thing.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
12 years agostaging/iio/mxs-lradc: fix preenable for multiple buffers
Michał Mirosław [Sat, 4 May 2013 13:19:00 +0000 (14:19 +0100)]
staging/iio/mxs-lradc: fix preenable for multiple buffers

This fixes 'preenable failed: -EINVAL' error when using this driver.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
12 years agoARM: 7729/1: vfp: ensure VFP_arch is non-zero when VFP is not supported
Will Deacon [Thu, 16 May 2013 18:38:51 +0000 (19:38 +0100)]
ARM: 7729/1: vfp: ensure VFP_arch is non-zero when VFP is not supported

Commit d3f79584a8b5 ("ARM: cleanup undefined instruction entry code")
improved the register scheduling when handling undefined instructions.
A side effect of this is that r5 is now used as a temporary, whilst the
VFP probing code relies on r5 containing a non-zero value when VFP is
not supported.

This patch fixes the VFP detection code so that we don't rely on the
contents of r5. Without this patch, Linux dies loudly on CPUs without
VFP support.

Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
12 years agoARM: 7727/1: remove the .vm_mm value from gate_vma
Steven Capper [Thu, 16 May 2013 16:16:11 +0000 (17:16 +0100)]
ARM: 7727/1: remove the .vm_mm value from gate_vma

If one reads /proc/$PID/smaps, the mmap_sem belonging to the
address space of the task being examined is locked for reading.
All the pages of the vmas belonging to the task's address space
are then walked with this lock held.

If a gate_vma is present in the architecture, it too is examined
by the fs/proc/task_mmu.c code. As gate_vma doesn't belong to the
address space of the task though, its pages are not walked.

A recent cleanup (commit f6604efe) of the gate_vma initialisation
code set the vm_mm value to &init_mm. Unfortunately a non-NULL
vm_mm value in the gate_vma will cause the task_mmu code to attempt
to walk the pages of the gate_vma (with no mmap-sem lock held). If
one enables Transparent Huge Page support and vm debugging, this
will then cause OOPses as pmd_trans_huge_lock is called without
mmap_sem being locked.

This patch removes the .vm_mm value from gate_vma, restoring the
original behaviour of the task_mmu code.

Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
12 years agoARM: 7723/1: crypto: sha1-armv4-large.S: fix SP handling
Ard Biesheuvel [Wed, 15 May 2013 09:46:30 +0000 (10:46 +0100)]
ARM: 7723/1: crypto: sha1-armv4-large.S: fix SP handling

Make the SHA1 asm code ABI conformant by making sure all stack
accesses occur above the stack pointer.

Origin:
http://git.openssl.org/gitweb/?p=openssl.git;a=commit;h=1a9d60d2

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
12 years agoMerge tag 'renesas-boards-marzen-fixes-for-v3.10' of git://git.kernel.org/pub/scm...
Olof Johansson [Wed, 22 May 2013 20:11:11 +0000 (13:11 -0700)]
Merge tag 'renesas-boards-marzen-fixes-for-v3.10' of git://git./linux/kernel/git/horms/renesas into fixes

From Simon Horman:
Correct USB PHY initialisation on the marzen board.

* tag 'renesas-boards-marzen-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: marzen: Use error values in usb_power_*

Signed-off-by: Olof Johansson <olof@lixom.net>
12 years agoMerge tag 'omap-fixes-a-for-3.10-rc' of git://git.kernel.org/pub/scm/linux/kernel...
Olof Johansson [Wed, 22 May 2013 20:09:20 +0000 (13:09 -0700)]
Merge tag 'omap-fixes-a-for-3.10-rc' of git://git./linux/kernel/git/pjw/omap-pending into fixes

From Paul Walmsley:
Fix the OMAP serial driver to work correctly on OMAP4 when booting
with DT.

* tag 'omap-fixes-a-for-3.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
  ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis
  SERIAL: OMAP: Remove the slave idle handling from the driver
  ARM: OMAP2+: serial: Remove the un-used slave idle hooks
  ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes
  ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active
  ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc()

Signed-off-by: Olof Johansson <olof@lixom.net>
12 years agoavr32: fix building warnings caused by redefinitions of HZ
Jiang Liu [Fri, 17 May 2013 15:45:18 +0000 (23:45 +0800)]
avr32: fix building warnings caused by redefinitions of HZ

As suggested by David Howells <dhowells@redhat.com>, use
asm-generic/param.h and uapi/asm-generic/param.h for AVR32.

It also fixes building warnings caused by redefinitions of HZ:
In file included from /ws/linux/kernel/linux.git/include/uapi/linux/param.h:4,
                 from include/linux/timex.h:63,
                 from include/linux/jiffies.h:8,
                 from include/linux/ktime.h:25,
                 from include/linux/timer.h:5,
                 from include/linux/workqueue.h:8,
                 from include/linux/srcu.h:34,
                 from include/linux/notifier.h:15,
                 from include/linux/memory_hotplug.h:6,
                 from include/linux/mmzone.h:777,
                 from include/linux/gfp.h:4,
                 from arch/avr32/mm/init.c:10:
/ws/linux/kernel/linux.git/arch/avr32/include/asm/param.h:6:1: warning: "HZ" redefined
In file included from /ws/linux/kernel/linux.git/arch/avr32/include/asm/param.h:4,
                 from /ws/linux/kernel/linux.git/include/uapi/linux/param.h:4,
                 from include/linux/timex.h:63,
                 from include/linux/jiffies.h:8,
                 from include/linux/ktime.h:25,
                 from include/linux/timer.h:5,
                 from include/linux/workqueue.h:8,
                 from include/linux/srcu.h:34,
                 from include/linux/notifier.h:15,
                 from include/linux/memory_hotplug.h:6,
                 from include/linux/mmzone.h:777,
                 from include/linux/gfp.h:4,
                 from arch/avr32/mm/init.c:10:
/ws/linux/kernel/linux.git/arch/avr32/include/uapi/asm/param.h:6:1: warning: this is the location of the previous definition

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>