Code cleanup.
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
#ifndef _bcmchip_h_
#define _bcmchip_h_
-/* Core reg address translation */
-#define CORE_CC_REG(base, field) (base + offsetof(chipcregs_t, field))
-#define CORE_BUS_REG(base, field) (base + offsetof(sdpcmd_regs_t, field))
-#define CORE_SB(base, field) \
- (base + SBCONFIGOFF + offsetof(sbconfig_t, field))
-
/* bcm4329 */
/* SDIO device core, ID 0x829 */
#define BCM4329_CORE_BUS_BASE 0x18011000
/* Flags for SDH calls */
#define F2SYNC (SDIO_REQ_4BYTE | SDIO_REQ_FIXED)
+/* sbimstate */
+#define SBIM_IBE 0x20000 /* inbanderror */
+#define SBIM_TO 0x40000 /* timeout */
+#define SBIM_BY 0x01800000 /* busy (sonics >= 2.3) */
+#define SBIM_RJ 0x02000000 /* reject (sonics >= 2.3) */
+
+/* sbtmstatelow */
+#define SBTML_RESET 0x0001 /* reset */
+#define SBTML_REJ_MASK 0x0006 /* reject field */
+#define SBTML_REJ 0x0002 /* reject */
+#define SBTML_TMPREJ 0x0004 /* temporary reject, for error recovery */
+
+#define SBTML_SICF_SHIFT 16 /* Shift to locate the SI control flags in sbtml */
+
+/* sbtmstatehigh */
+#define SBTMH_SERR 0x0001 /* serror */
+#define SBTMH_INT 0x0002 /* interrupt */
+#define SBTMH_BUSY 0x0004 /* busy */
+#define SBTMH_TO 0x0020 /* timeout (sonics >= 2.3) */
+
+#define SBTMH_SISF_SHIFT 16 /* Shift to locate the SI status flags in sbtmh */
+
+/* sbidlow */
+#define SBIDL_INIT 0x80 /* initiator */
+
+/* sbidhigh */
+#define SBIDH_RC_MASK 0x000f /* revision code */
+#define SBIDH_RCE_MASK 0x7000 /* revision code extension field */
+#define SBIDH_RCE_SHIFT 8
+#define SBCOREREV(sbidh) \
+ ((((sbidh) & SBIDH_RCE_MASK) >> SBIDH_RCE_SHIFT) | ((sbidh) & SBIDH_RC_MASK))
+#define SBIDH_CC_MASK 0x8ff0 /* core code */
+#define SBIDH_CC_SHIFT 4
+#define SBIDH_VC_MASK 0xffff0000 /* vendor code */
+#define SBIDH_VC_SHIFT 16
+
/*
* Conversion of 802.1D priority to precedence level
*/
extern int dhdcdc_set_ioctl(dhd_pub_t *dhd, int ifidx, uint cmd, void *buf,
uint len);
+/* Core reg address translation */
+#define CORE_CC_REG(base, field) (base + offsetof(chipcregs_t, field))
+#define CORE_BUS_REG(base, field) (base + offsetof(sdpcmd_regs_t, field))
+#define CORE_SB(base, field) \
+ (base + SBCONFIGOFF + offsetof(sbconfig_t, field))
+
#ifdef DHD_DEBUG
/* Device console log buffer state */
typedef struct dhd_console {
bool ctrl_frame_stat;
} dhd_bus_t;
+#ifndef _LANGUAGE_ASSEMBLY
+
+typedef volatile struct _sbconfig {
+ u32 PAD[2];
+ u32 sbipsflag; /* initiator port ocp slave flag */
+ u32 PAD[3];
+ u32 sbtpsflag; /* target port ocp slave flag */
+ u32 PAD[11];
+ u32 sbtmerrloga; /* (sonics >= 2.3) */
+ u32 PAD;
+ u32 sbtmerrlog; /* (sonics >= 2.3) */
+ u32 PAD[3];
+ u32 sbadmatch3; /* address match3 */
+ u32 PAD;
+ u32 sbadmatch2; /* address match2 */
+ u32 PAD;
+ u32 sbadmatch1; /* address match1 */
+ u32 PAD[7];
+ u32 sbimstate; /* initiator agent state */
+ u32 sbintvec; /* interrupt mask */
+ u32 sbtmstatelow; /* target state */
+ u32 sbtmstatehigh; /* target state */
+ u32 sbbwa0; /* bandwidth allocation table0 */
+ u32 PAD;
+ u32 sbimconfiglow; /* initiator configuration */
+ u32 sbimconfighigh; /* initiator configuration */
+ u32 sbadmatch0; /* address match0 */
+ u32 PAD;
+ u32 sbtmconfiglow; /* target configuration */
+ u32 sbtmconfighigh; /* target configuration */
+ u32 sbbconfig; /* broadcast configuration */
+ u32 PAD;
+ u32 sbbstate; /* broadcast state */
+ u32 PAD[3];
+ u32 sbactcnfg; /* activate configuration */
+ u32 PAD[3];
+ u32 sbflagst; /* current sbflags */
+ u32 PAD[3];
+ u32 sbidlow; /* identification */
+ u32 sbidhigh; /* identification */
+} sbconfig_t;
+
+#endif /* _LANGUAGE_ASSEMBLY */
+
/* clkstate */
#define CLK_NONE 0
#define CLK_SDONLY 1
#define PAD _XSTR(__LINE__)
#endif /* PAD */
+/* dma registers per channel(xmt or rcv) */
+typedef volatile struct {
+ u32 control; /* enable, et al */
+ u32 addr; /* descriptor ring base address (4K aligned) */
+ u32 ptr; /* last descriptor posted to chip */
+ u32 status; /* current active descriptor, et al */
+} dma32regs_t;
+
+typedef volatile struct {
+ dma32regs_t xmt; /* dma tx channel */
+ dma32regs_t rcv; /* dma rx channel */
+} dma32regp_t;
+
typedef volatile struct {
dma64regs_t xmt; /* dma tx */
u32 PAD[2];
u32 PAD[2];
} dma64p_t;
+
+typedef volatile struct { /* diag access */
+ u32 fifoaddr; /* diag address */
+ u32 fifodatalow; /* low 32bits of data */
+ u32 fifodatahigh; /* high 32bits of data */
+ u32 pad; /* reserved */
+} dma64diag_t;
+
/* dma64 sdiod corerev >= 1 */
typedef volatile struct {
dma64p_t dma64regs[2];
u32 PAD[464];
/* Sonics SiliconBackplane registers */
- sbconfig_t sbconfig; /* SbConfig Regs, 0xf00-0xfff, rev8 */
+ u16 PAD[0x80]; /* SbConfig Regs, 0xf00-0xfff, rev8 */
} sdpcmd_regs_t;
/* corecontrol */
#include <bcmsrom.h>
#include <wlc_pmu.h>
+/* slow_clk_ctl */
+#define SCC_SS_MASK 0x00000007 /* slow clock source mask */
+#define SCC_SS_LPO 0x00000000 /* source of slow clock is LPO */
+#define SCC_SS_XTAL 0x00000001 /* source of slow clock is crystal */
+#define SCC_SS_PCI 0x00000002 /* source of slow clock is PCI */
+#define SCC_LF 0x00000200 /* LPOFreqSel, 1: 160Khz, 0: 32KHz */
+#define SCC_LP 0x00000400 /* LPOPowerDown, 1: LPO is disabled,
+ * 0: LPO is enabled
+ */
+#define SCC_FS 0x00000800 /* ForceSlowClk, 1: sb/cores running on slow clock,
+ * 0: power logic control
+ */
+#define SCC_IP 0x00001000 /* IgnorePllOffReq, 1/0: power logic ignores/honors
+ * PLL clock disable requests from core
+ */
+#define SCC_XC 0x00002000 /* XtalControlEn, 1/0: power logic does/doesn't
+ * disable crystal when appropriate
+ */
+#define SCC_XP 0x00004000 /* XtalPU (RO), 1/0: crystal running/disabled */
+#define SCC_CD_MASK 0xffff0000 /* ClockDivider (SlowClk = 1/(4+divisor)) */
+#define SCC_CD_SHIFT 16
+
+/* system_clk_ctl */
+#define SYCC_IE 0x00000001 /* ILPen: Enable Idle Low Power */
+#define SYCC_AE 0x00000002 /* ALPen: Enable Active Low Power */
+#define SYCC_FP 0x00000004 /* ForcePLLOn */
+#define SYCC_AR 0x00000008 /* Force ALP (or HT if ALPen is not set */
+#define SYCC_HR 0x00000010 /* Force HT */
+#define SYCC_CD_MASK 0xffff0000 /* ClkDiv (ILP = 1/(4 * (divisor + 1)) */
+#define SYCC_CD_SHIFT 16
+
+#define CST4329_SPROM_OTP_SEL_MASK 0x00000003
+#define CST4329_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */
+#define CST4329_SPROM_SEL 1 /* OTP is powered up, SPROM is present */
+#define CST4329_OTP_SEL 2 /* OTP is powered up, no SPROM */
+#define CST4329_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */
+#define CST4329_SPI_SDIO_MODE_MASK 0x00000004
+#define CST4329_SPI_SDIO_MODE_SHIFT 2
+
+/* 43224 chip-specific ChipControl register bits */
+#define CCTRL43224_GPIO_TOGGLE 0x8000
+#define CCTRL_43224A0_12MA_LED_DRIVE 0x00F000F0 /* 12 mA drive strength */
+#define CCTRL_43224B0_12MA_LED_DRIVE 0xF0 /* 12 mA drive strength for later 43224s */
+
+/* 43236 Chip specific ChipStatus register bits */
+#define CST43236_SFLASH_MASK 0x00000040
+#define CST43236_OTP_MASK 0x00000080
+#define CST43236_HSIC_MASK 0x00000100 /* USB/HSIC */
+#define CST43236_BP_CLK 0x00000200 /* 120/96Mbps */
+#define CST43236_BOOT_MASK 0x00001800
+#define CST43236_BOOT_SHIFT 11
+#define CST43236_BOOT_FROM_SRAM 0 /* boot from SRAM, ARM in reset */
+#define CST43236_BOOT_FROM_ROM 1 /* boot from ROM */
+#define CST43236_BOOT_FROM_FLASH 2 /* boot from FLASH */
+#define CST43236_BOOT_FROM_INVALID 3
+
+/* 4331 chip-specific ChipControl register bits */
+#define CCTRL4331_BT_COEXIST (1<<0) /* 0 disable */
+#define CCTRL4331_SECI (1<<1) /* 0 SECI is disabled (JATG functional) */
+#define CCTRL4331_EXT_LNA (1<<2) /* 0 disable */
+#define CCTRL4331_SPROM_GPIO13_15 (1<<3) /* sprom/gpio13-15 mux */
+#define CCTRL4331_EXTPA_EN (1<<4) /* 0 ext pa disable, 1 ext pa enabled */
+#define CCTRL4331_GPIOCLK_ON_SPROMCS (1<<5) /* set drive out GPIO_CLK on sprom_cs pin */
+#define CCTRL4331_PCIE_MDIO_ON_SPROMCS (1<<6) /* use sprom_cs pin as PCIE mdio interface */
+#define CCTRL4331_EXTPA_ON_GPIO2_5 (1<<7) /* aband extpa will be at gpio2/5 and sprom_dout */
+#define CCTRL4331_OVR_PIPEAUXCLKEN (1<<8) /* override core control on pipe_AuxClkEnable */
+#define CCTRL4331_OVR_PIPEAUXPWRDOWN (1<<9) /* override core control on pipe_AuxPowerDown */
+#define CCTRL4331_PCIE_AUXCLKEN (1<<10) /* pcie_auxclkenable */
+#define CCTRL4331_PCIE_PIPE_PLLDOWN (1<<11) /* pcie_pipe_pllpowerdown */
+#define CCTRL4331_BT_SHD0_ON_GPIO4 (1<<16) /* enable bt_shd0 at gpio4 */
+#define CCTRL4331_BT_SHD1_ON_GPIO5 (1<<17) /* enable bt_shd1 at gpio5 */
+
+/* 4331 Chip specific ChipStatus register bits */
+#define CST4331_XTAL_FREQ 0x00000001 /* crystal frequency 20/40Mhz */
+#define CST4331_SPROM_PRESENT 0x00000002
+#define CST4331_OTP_PRESENT 0x00000004
+#define CST4331_LDO_RF 0x00000008
+#define CST4331_LDO_PAR 0x00000010
+
+/* 4319 chip-specific ChipStatus register bits */
+#define CST4319_SPI_CPULESSUSB 0x00000001
+#define CST4319_SPI_CLK_POL 0x00000002
+#define CST4319_SPI_CLK_PH 0x00000008
+#define CST4319_SPROM_OTP_SEL_MASK 0x000000c0 /* gpio [7:6], SDIO CIS selection */
+#define CST4319_SPROM_OTP_SEL_SHIFT 6
+#define CST4319_DEFCIS_SEL 0x00000000 /* use default CIS, OTP is powered up */
+#define CST4319_SPROM_SEL 0x00000040 /* use SPROM, OTP is powered up */
+#define CST4319_OTP_SEL 0x00000080 /* use OTP, OTP is powered up */
+#define CST4319_OTP_PWRDN 0x000000c0 /* use SPROM, OTP is powered down */
+#define CST4319_SDIO_USB_MODE 0x00000100 /* gpio [8], sdio/usb mode */
+#define CST4319_REMAP_SEL_MASK 0x00000600
+#define CST4319_ILPDIV_EN 0x00000800
+#define CST4319_XTAL_PD_POL 0x00001000
+#define CST4319_LPO_SEL 0x00002000
+#define CST4319_RES_INIT_MODE 0x0000c000
+#define CST4319_PALDO_EXTPNP 0x00010000 /* PALDO is configured with external PNP */
+#define CST4319_CBUCK_MODE_MASK 0x00060000
+#define CST4319_CBUCK_MODE_BURST 0x00020000
+#define CST4319_CBUCK_MODE_LPBURST 0x00060000
+#define CST4319_RCAL_VALID 0x01000000
+#define CST4319_RCAL_VALUE_MASK 0x3e000000
+#define CST4319_RCAL_VALUE_SHIFT 25
+
+/* 4336 chip-specific ChipStatus register bits */
+#define CST4336_SPI_MODE_MASK 0x00000001
+#define CST4336_SPROM_PRESENT 0x00000002
+#define CST4336_OTP_PRESENT 0x00000004
+#define CST4336_ARMREMAP_0 0x00000008
+#define CST4336_ILPDIV_EN_MASK 0x00000010
+#define CST4336_ILPDIV_EN_SHIFT 4
+#define CST4336_XTAL_PD_POL_MASK 0x00000020
+#define CST4336_XTAL_PD_POL_SHIFT 5
+#define CST4336_LPO_SEL_MASK 0x00000040
+#define CST4336_LPO_SEL_SHIFT 6
+#define CST4336_RES_INIT_MODE_MASK 0x00000180
+#define CST4336_RES_INIT_MODE_SHIFT 7
+#define CST4336_CBUCK_MODE_MASK 0x00000600
+#define CST4336_CBUCK_MODE_SHIFT 9
+
+/* 4313 chip-specific ChipStatus register bits */
+#define CST4313_SPROM_PRESENT 1
+#define CST4313_OTP_PRESENT 2
+#define CST4313_SPROM_OTP_SEL_MASK 0x00000002
+#define CST4313_SPROM_OTP_SEL_SHIFT 0
+
+/* 4313 Chip specific ChipControl register bits */
+#define CCTRL_4313_12MA_LED_DRIVE 0x00000007 /* 12 mA drive strengh for later 4313 */
+
#define BCM47162_DMP() ((sih->chip == BCM47162_CHIP_ID) && \
(sih->chiprev == 0) && \
(sii->coreid[sii->curidx] == MIPS74K_CORE_ID))
#define BISZ_BSSEND_IDX 6 /* 6: bss end */
#define BISZ_SIZE 7 /* descriptor size in 32-bit integers */
+#define CC_SROM_OTP 0x800 /* SROM/OTP address space */
+
+/* gpiotimerval */
+#define GPIO_ONTIME_SHIFT 16
+
+/* Fields in clkdiv */
+#define CLKD_OTP 0x000f0000
+#define CLKD_OTP_SHIFT 16
+
+/* When Srom support present, fields in sromcontrol */
+#define SRC_START 0x80000000
+#define SRC_BUSY 0x80000000
+#define SRC_OPCODE 0x60000000
+#define SRC_OP_READ 0x00000000
+#define SRC_OP_WRITE 0x20000000
+#define SRC_OP_WRDIS 0x40000000
+#define SRC_OP_WREN 0x60000000
+#define SRC_OTPSEL 0x00000010
+#define SRC_LOCK 0x00000008
+#define SRC_SIZE_MASK 0x00000006
+#define SRC_SIZE_1K 0x00000000
+#define SRC_SIZE_4K 0x00000002
+#define SRC_SIZE_16K 0x00000004
+#define SRC_SIZE_SHIFT 1
+#define SRC_PRESENT 0x00000001
+
+/* 4330 chip-specific ChipStatus register bits */
+#define CST4330_CHIPMODE_SDIOD(cs) (((cs) & 0x7) < 6) /* SDIO || gSPI */
+#define CST4330_CHIPMODE_USB20D(cs) (((cs) & 0x7) >= 6) /* USB || USBDA */
+#define CST4330_CHIPMODE_SDIO(cs) (((cs) & 0x4) == 0) /* SDIO */
+#define CST4330_CHIPMODE_GSPI(cs) (((cs) & 0x6) == 4) /* gSPI */
+#define CST4330_CHIPMODE_USB(cs) (((cs) & 0x7) == 6) /* USB packet-oriented */
+#define CST4330_CHIPMODE_USBDA(cs) (((cs) & 0x7) == 7) /* USB Direct Access */
+#define CST4330_OTP_PRESENT 0x00000010
+#define CST4330_LPO_AUTODET_EN 0x00000020
+#define CST4330_ARMREMAP_0 0x00000040
+#define CST4330_SPROM_PRESENT 0x00000080 /* takes priority over OTP if both set */
+#define CST4330_ILPDIV_EN 0x00000100
+#define CST4330_LPO_SEL 0x00000200
+#define CST4330_RES_INIT_MODE_SHIFT 10
+#define CST4330_RES_INIT_MODE_MASK 0x00000c00
+#define CST4330_CBUCK_MODE_SHIFT 12
+#define CST4330_CBUCK_MODE_MASK 0x00003000
+#define CST4330_CBUCK_POWER_OK 0x00004000
+#define CST4330_BB_PLL_LOCKED 0x00008000
+
#define SI_INFO(sih) (si_info_t *)sih
#define GOODCOREADDR(x, b) \
#include <sbchipc.h>
#include <bcmotp.h>
+#define OTPS_GUP_MASK 0x00000f00
+#define OTPS_GUP_SHIFT 8
+#define OTPS_GUP_HW 0x00000100 /* h/w subregion is programmed */
+#define OTPS_GUP_SW 0x00000200 /* s/w subregion is programmed */
+#define OTPS_GUP_CI 0x00000400 /* chipid/pkgopt subregion is programmed */
+#define OTPS_GUP_FUSE 0x00000800 /* fuse subregion is programmed */
+
+/* Fields in otpprog in rev >= 21 and HND OTP */
+#define OTPP_COL_MASK 0x000000ff
+#define OTPP_COL_SHIFT 0
+#define OTPP_ROW_MASK 0x0000ff00
+#define OTPP_ROW_SHIFT 8
+#define OTPP_OC_MASK 0x0f000000
+#define OTPP_OC_SHIFT 24
+#define OTPP_READERR 0x10000000
+#define OTPP_VALUE_MASK 0x20000000
+#define OTPP_VALUE_SHIFT 29
+#define OTPP_START_BUSY 0x80000000
+#define OTPP_READ 0x40000000 /* HND OTP */
+
+/* Opcodes for OTPP_OC field */
+#define OTPPOC_READ 0
+#define OTPPOC_BIT_PROG 1
+#define OTPPOC_VERIFY 3
+#define OTPPOC_INIT 4
+#define OTPPOC_SET 5
+#define OTPPOC_RESET 6
+#define OTPPOC_OCST 7
+#define OTPPOC_ROW_LOCK 8
+#define OTPPOC_PRESCN_TEST 9
+
/*
* There are two different OTP controllers so far:
* 1. new IPX OTP controller: chipc 21, >=23
#define _D11_H
#include <linux/ieee80211.h>
-#include <sbconfig.h>
/* cpp contortions to concatenate w/arg prescan */
#ifndef PAD
/* SHM *//* 0x800 - 0xEFE */
u16 PAD[0x380]; /* 0x800 - 0xEFE */
-
- /* SB configuration registers: 0xF00 */
- sbconfig_t sbconfig; /* sb config regs occupy top 256 bytes */
} d11regs_t;
#define PIHR_BASE 0x0400 /* byte address of packed IHR region */
#include <asm/addrspace.h>
#endif
+/*
+ * Each descriptor ring must be 8kB aligned, and fit within a contiguous 8kB physical address.
+ */
+#define D64RINGALIGN_BITS 13
+#define D64MAXRINGSZ (1 << D64RINGALIGN_BITS)
+#define D64RINGALIGN (1 << D64RINGALIGN_BITS)
+
+#define D64MAXDD (D64MAXRINGSZ / sizeof (dma64dd_t))
+
+/* transmit channel control */
+#define D64_XC_XE 0x00000001 /* transmit enable */
+#define D64_XC_SE 0x00000002 /* transmit suspend request */
+#define D64_XC_LE 0x00000004 /* loopback enable */
+#define D64_XC_FL 0x00000010 /* flush request */
+#define D64_XC_PD 0x00000800 /* parity check disable */
+#define D64_XC_AE 0x00030000 /* address extension bits */
+#define D64_XC_AE_SHIFT 16
+
+/* transmit descriptor table pointer */
+#define D64_XP_LD_MASK 0x00000fff /* last valid descriptor */
+
+/* transmit channel status */
+#define D64_XS0_CD_MASK 0x00001fff /* current descriptor pointer */
+#define D64_XS0_XS_MASK 0xf0000000 /* transmit state */
+#define D64_XS0_XS_SHIFT 28
+#define D64_XS0_XS_DISABLED 0x00000000 /* disabled */
+#define D64_XS0_XS_ACTIVE 0x10000000 /* active */
+#define D64_XS0_XS_IDLE 0x20000000 /* idle wait */
+#define D64_XS0_XS_STOPPED 0x30000000 /* stopped */
+#define D64_XS0_XS_SUSP 0x40000000 /* suspend pending */
+
+#define D64_XS1_AD_MASK 0x00001fff /* active descriptor */
+#define D64_XS1_XE_MASK 0xf0000000 /* transmit errors */
+#define D64_XS1_XE_SHIFT 28
+#define D64_XS1_XE_NOERR 0x00000000 /* no error */
+#define D64_XS1_XE_DPE 0x10000000 /* descriptor protocol error */
+#define D64_XS1_XE_DFU 0x20000000 /* data fifo underrun */
+#define D64_XS1_XE_DTE 0x30000000 /* data transfer error */
+#define D64_XS1_XE_DESRE 0x40000000 /* descriptor read error */
+#define D64_XS1_XE_COREE 0x50000000 /* core error */
+
+/* receive channel control */
+#define D64_RC_RE 0x00000001 /* receive enable */
+#define D64_RC_RO_MASK 0x000000fe /* receive frame offset */
+#define D64_RC_RO_SHIFT 1
+#define D64_RC_FM 0x00000100 /* direct fifo receive (pio) mode */
+#define D64_RC_SH 0x00000200 /* separate rx header descriptor enable */
+#define D64_RC_OC 0x00000400 /* overflow continue */
+#define D64_RC_PD 0x00000800 /* parity check disable */
+#define D64_RC_AE 0x00030000 /* address extension bits */
+#define D64_RC_AE_SHIFT 16
+
+/* flags for dma controller */
+#define DMA_CTRL_PEN (1 << 0) /* partity enable */
+#define DMA_CTRL_ROC (1 << 1) /* rx overflow continue */
+#define DMA_CTRL_RXMULTI (1 << 2) /* allow rx scatter to multiple descriptors */
+#define DMA_CTRL_UNFRAMED (1 << 3) /* Unframed Rx/Tx data */
+
+/* receive descriptor table pointer */
+#define D64_RP_LD_MASK 0x00000fff /* last valid descriptor */
+
+/* receive channel status */
+#define D64_RS0_CD_MASK 0x00001fff /* current descriptor pointer */
+#define D64_RS0_RS_MASK 0xf0000000 /* receive state */
+#define D64_RS0_RS_SHIFT 28
+#define D64_RS0_RS_DISABLED 0x00000000 /* disabled */
+#define D64_RS0_RS_ACTIVE 0x10000000 /* active */
+#define D64_RS0_RS_IDLE 0x20000000 /* idle wait */
+#define D64_RS0_RS_STOPPED 0x30000000 /* stopped */
+#define D64_RS0_RS_SUSP 0x40000000 /* suspend pending */
+
+#define D64_RS1_AD_MASK 0x0001ffff /* active descriptor */
+#define D64_RS1_RE_MASK 0xf0000000 /* receive errors */
+#define D64_RS1_RE_SHIFT 28
+#define D64_RS1_RE_NOERR 0x00000000 /* no error */
+#define D64_RS1_RE_DPO 0x10000000 /* descriptor protocol error */
+#define D64_RS1_RE_DFU 0x20000000 /* data fifo overflow */
+#define D64_RS1_RE_DTE 0x30000000 /* data transfer error */
+#define D64_RS1_RE_DESRE 0x40000000 /* descriptor read error */
+#define D64_RS1_RE_COREE 0x50000000 /* core error */
+
+/* fifoaddr */
+#define D64_FA_OFF_MASK 0xffff /* offset */
+#define D64_FA_SEL_MASK 0xf0000 /* select */
+#define D64_FA_SEL_SHIFT 16
+#define D64_FA_SEL_XDD 0x00000 /* transmit dma data */
+#define D64_FA_SEL_XDP 0x10000 /* transmit dma pointers */
+#define D64_FA_SEL_RDD 0x40000 /* receive dma data */
+#define D64_FA_SEL_RDP 0x50000 /* receive dma pointers */
+#define D64_FA_SEL_XFD 0x80000 /* transmit fifo data */
+#define D64_FA_SEL_XFP 0x90000 /* transmit fifo pointers */
+#define D64_FA_SEL_RFD 0xc0000 /* receive fifo data */
+#define D64_FA_SEL_RFP 0xd0000 /* receive fifo pointers */
+#define D64_FA_SEL_RSD 0xe0000 /* receive frame status data */
+#define D64_FA_SEL_RSP 0xf0000 /* receive frame status pointers */
+
+/* descriptor control flags 1 */
+#define D64_CTRL_COREFLAGS 0x0ff00000 /* core specific flags */
+#define D64_CTRL1_EOT ((u32)1 << 28) /* end of descriptor table */
+#define D64_CTRL1_IOC ((u32)1 << 29) /* interrupt on completion */
+#define D64_CTRL1_EOF ((u32)1 << 30) /* end of frame */
+#define D64_CTRL1_SOF ((u32)1 << 31) /* start of frame */
+
+/* descriptor control flags 2 */
+#define D64_CTRL2_BC_MASK 0x00007fff /* buffer byte count. real data len must <= 16KB */
+#define D64_CTRL2_AE 0x00030000 /* address extension bits */
+#define D64_CTRL2_AE_SHIFT 16
+#define D64_CTRL2_PARITY 0x00040000 /* parity bit */
+
+/* control flags in the range [27:20] are core-specific and not defined here */
+#define D64_CTRL_CORE_MASK 0x0ff00000
+
+#define D64_RX_FRM_STS_LEN 0x0000ffff /* frame length mask */
+#define D64_RX_FRM_STS_OVFL 0x00800000 /* RxOverFlow */
+#define D64_RX_FRM_STS_DSCRCNT 0x0f000000 /* no. of descriptors used - 1 */
+#define D64_RX_FRM_STS_DATATYPE 0xf0000000 /* core-dependent data type */
+
/* debug/trace */
#ifdef BCMDBG
#define DMA_ERROR(args) \
#define R_SM(r) (*(r))
#define W_SM(r, v) (*(r) = (v))
+/*
+ * DMA Descriptor
+ * Descriptors are only read by the hardware, never written back.
+ */
+typedef volatile struct {
+ u32 ctrl1; /* misc control bits & bufcount */
+ u32 ctrl2; /* buffer count and address extension */
+ u32 addrlow; /* memory address of the date buffer, bits 31:0 */
+ u32 addrhigh; /* memory address of the date buffer, bits 63:32 */
+} dma64dd_t;
+
/* dma engine software state */
typedef struct dma_info {
struct dma_pub dma; /* exported structure */
#include <nicpci.h>
#include <pcicfg.h>
+/* chipcontrol */
+#define CHIPCTRL_4321_PLL_DOWN 0x800000 /* serdes PLL down override */
+
typedef struct {
union {
sbpcieregs_t *pcieregs;
#define NPHY_ADJUSTED_MINCRSPOWER 0x1e
+/* 5357 Chip specific ChipControl register bits */
+#define CCTRL5357_EXTPA (1<<14) /* extPA in ChipControl 1, bit 14 */
+#define CCTRL5357_ANT_MUX_2o3 (1<<15) /* 2o3 in ChipControl 1, bit 15 */
+
typedef struct _nphy_iqcal_params {
u16 txlpf;
u16 txgm;
#include <bcmotp.h>
#include <bcmutils.h>
#include <bcmnvram.h>
-#include <sbconfig.h>
#include <sbchipc.h>
#include <pcicfg.h>
#include <sbdma.h>
#include <bcmutils.h>
#include <bcmwifi.h>
#include <aiutils.h>
-#include <sbconfig.h>
#include <sbchipc.h>
#include <pcicfg.h>
#include <sbdma.h>
#define RES_DEPEND_ADD 1
#define RES_DEPEND_REMOVE -1
+/* Fields in pmucontrol */
+#define PCTL_ILP_DIV_MASK 0xffff0000
+#define PCTL_ILP_DIV_SHIFT 16
+#define PCTL_PLL_PLLCTL_UPD 0x00000400 /* rev 2 */
+#define PCTL_NOILP_ON_WAIT 0x00000200 /* rev 1 */
+#define PCTL_HT_REQ_EN 0x00000100
+#define PCTL_ALP_REQ_EN 0x00000080
+#define PCTL_XTALFREQ_MASK 0x0000007c
+#define PCTL_XTALFREQ_SHIFT 2
+#define PCTL_ILP_DIV_EN 0x00000002
+#define PCTL_LPO_SEL 0x00000001
+
+/* Fields in clkstretch */
+#define CSTRETCH_HT 0xffff0000
+#define CSTRETCH_ALP 0x0000ffff
+
/* d11 slow to fast clock transition time in slow clock cycles */
#define D11SCC_SLOW2FAST_TRANSITION 2
+/* ILP clock */
+#define ILP_CLOCK 32000
+
+/* ALP clock on pre-PMU chips */
+#define ALP_CLOCK 20000000
+
+/* HT clock */
+#define HT_CLOCK 80000000
+
+#define OTPS_READY 0x00001000
+
+/* pmustatus */
+#define PST_EXTLPOAVAIL 0x0100
+#define PST_WDRESET 0x0080
+#define PST_INTPEND 0x0040
+#define PST_SBCLKST 0x0030
+#define PST_SBCLKST_ILP 0x0010
+#define PST_SBCLKST_ALP 0x0020
+#define PST_SBCLKST_HT 0x0030
+#define PST_ALPAVAIL 0x0008
+#define PST_HTAVAIL 0x0004
+#define PST_RESINIT 0x0003
+
+/* PMU Resource Request Timer registers */
+/* This is based on PmuRev0 */
+#define PRRT_TIME_MASK 0x03ff
+#define PRRT_INTEN 0x0400
+#define PRRT_REQ_ACTIVE 0x0800
+#define PRRT_ALP_REQ 0x1000
+#define PRRT_HT_REQ 0x2000
+
+/* PMU resource bit position */
+#define PMURES_BIT(bit) (1 << (bit))
+
+/* PMU resource number limit */
+#define PMURES_MAX_RESNUM 30
+
+/* PMU chip control0 register */
+#define PMU_CHIPCTL0 0
+
+/* PMU chip control1 register */
+#define PMU_CHIPCTL1 1
+#define PMU_CC1_RXC_DLL_BYPASS 0x00010000
+
+#define PMU_CC1_IF_TYPE_MASK 0x00000030
+#define PMU_CC1_IF_TYPE_RMII 0x00000000
+#define PMU_CC1_IF_TYPE_MII 0x00000010
+#define PMU_CC1_IF_TYPE_RGMII 0x00000020
+
+#define PMU_CC1_SW_TYPE_MASK 0x000000c0
+#define PMU_CC1_SW_TYPE_EPHY 0x00000000
+#define PMU_CC1_SW_TYPE_EPHYMII 0x00000040
+#define PMU_CC1_SW_TYPE_EPHYRMII 0x00000080
+#define PMU_CC1_SW_TYPE_RGMII 0x000000c0
+
+/* PMU corerev and chip specific PLL controls.
+ * PMU<rev>_PLL<num>_XX where <rev> is PMU corerev and <num> is an arbitrary number
+ * to differentiate different PLLs controlled by the same PMU rev.
+ */
+/* pllcontrol registers */
+/* PDIV, div_phy, div_arm, div_adc, dith_sel, ioff, kpd_scale, lsb_sel, mash_sel, lf_c & lf_r */
+#define PMU0_PLL0_PLLCTL0 0
+#define PMU0_PLL0_PC0_PDIV_MASK 1
+#define PMU0_PLL0_PC0_PDIV_FREQ 25000
+#define PMU0_PLL0_PC0_DIV_ARM_MASK 0x00000038
+#define PMU0_PLL0_PC0_DIV_ARM_SHIFT 3
+#define PMU0_PLL0_PC0_DIV_ARM_BASE 8
+
+/* PC0_DIV_ARM for PLLOUT_ARM */
+#define PMU0_PLL0_PC0_DIV_ARM_110MHZ 0
+#define PMU0_PLL0_PC0_DIV_ARM_97_7MHZ 1
+#define PMU0_PLL0_PC0_DIV_ARM_88MHZ 2
+#define PMU0_PLL0_PC0_DIV_ARM_80MHZ 3 /* Default */
+#define PMU0_PLL0_PC0_DIV_ARM_73_3MHZ 4
+#define PMU0_PLL0_PC0_DIV_ARM_67_7MHZ 5
+#define PMU0_PLL0_PC0_DIV_ARM_62_9MHZ 6
+#define PMU0_PLL0_PC0_DIV_ARM_58_6MHZ 7
+
+/* Wildcard base, stop_mod, en_lf_tp, en_cal & lf_r2 */
+#define PMU0_PLL0_PLLCTL1 1
+#define PMU0_PLL0_PC1_WILD_INT_MASK 0xf0000000
+#define PMU0_PLL0_PC1_WILD_INT_SHIFT 28
+#define PMU0_PLL0_PC1_WILD_FRAC_MASK 0x0fffff00
+#define PMU0_PLL0_PC1_WILD_FRAC_SHIFT 8
+#define PMU0_PLL0_PC1_STOP_MOD 0x00000040
+
+/* Wildcard base, vco_calvar, vco_swc, vco_var_selref, vso_ical & vco_sel_avdd */
+#define PMU0_PLL0_PLLCTL2 2
+#define PMU0_PLL0_PC2_WILD_INT_MASK 0xf
+#define PMU0_PLL0_PC2_WILD_INT_SHIFT 4
+
+/* pllcontrol registers */
+/* ndiv_pwrdn, pwrdn_ch<x>, refcomp_pwrdn, dly_ch<x>, p1div, p2div, _bypass_sdmod */
+#define PMU1_PLL0_PLLCTL0 0
+#define PMU1_PLL0_PC0_P1DIV_MASK 0x00f00000
+#define PMU1_PLL0_PC0_P1DIV_SHIFT 20
+#define PMU1_PLL0_PC0_P2DIV_MASK 0x0f000000
+#define PMU1_PLL0_PC0_P2DIV_SHIFT 24
+
+/* m<x>div */
+#define PMU1_PLL0_PLLCTL1 1
+#define PMU1_PLL0_PC1_M1DIV_MASK 0x000000ff
+#define PMU1_PLL0_PC1_M1DIV_SHIFT 0
+#define PMU1_PLL0_PC1_M2DIV_MASK 0x0000ff00
+#define PMU1_PLL0_PC1_M2DIV_SHIFT 8
+#define PMU1_PLL0_PC1_M3DIV_MASK 0x00ff0000
+#define PMU1_PLL0_PC1_M3DIV_SHIFT 16
+#define PMU1_PLL0_PC1_M4DIV_MASK 0xff000000
+#define PMU1_PLL0_PC1_M4DIV_SHIFT 24
+
+#define PMU1_PLL0_CHIPCTL0 0
+#define PMU1_PLL0_CHIPCTL1 1
+#define PMU1_PLL0_CHIPCTL2 2
+
+#define DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT 8
+#define DOT11MAC_880MHZ_CLK_DIVISOR_MASK (0xFF << DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT)
+#define DOT11MAC_880MHZ_CLK_DIVISOR_VAL (0xE << DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT)
+
+/* m<x>div, ndiv_dither_mfb, ndiv_mode, ndiv_int */
+#define PMU1_PLL0_PLLCTL2 2
+#define PMU1_PLL0_PC2_M5DIV_MASK 0x000000ff
+#define PMU1_PLL0_PC2_M5DIV_SHIFT 0
+#define PMU1_PLL0_PC2_M6DIV_MASK 0x0000ff00
+#define PMU1_PLL0_PC2_M6DIV_SHIFT 8
+#define PMU1_PLL0_PC2_NDIV_MODE_MASK 0x000e0000
+#define PMU1_PLL0_PC2_NDIV_MODE_SHIFT 17
+#define PMU1_PLL0_PC2_NDIV_MODE_MASH 1
+#define PMU1_PLL0_PC2_NDIV_MODE_MFB 2 /* recommended for 4319 */
+#define PMU1_PLL0_PC2_NDIV_INT_MASK 0x1ff00000
+#define PMU1_PLL0_PC2_NDIV_INT_SHIFT 20
+
+/* ndiv_frac */
+#define PMU1_PLL0_PLLCTL3 3
+#define PMU1_PLL0_PC3_NDIV_FRAC_MASK 0x00ffffff
+#define PMU1_PLL0_PC3_NDIV_FRAC_SHIFT 0
+
+/* pll_ctrl */
+#define PMU1_PLL0_PLLCTL4 4
+
+/* pll_ctrl, vco_rng, clkdrive_ch<x> */
+#define PMU1_PLL0_PLLCTL5 5
+#define PMU1_PLL0_PC5_CLK_DRV_MASK 0xffffff00
+#define PMU1_PLL0_PC5_CLK_DRV_SHIFT 8
+
+/* PMU rev 2 control words */
+#define PMU2_PHY_PLL_PLLCTL 4
+#define PMU2_SI_PLL_PLLCTL 10
+
+/* PMU rev 2 */
+/* pllcontrol registers */
+/* ndiv_pwrdn, pwrdn_ch<x>, refcomp_pwrdn, dly_ch<x>, p1div, p2div, _bypass_sdmod */
+#define PMU2_PLL_PLLCTL0 0
+#define PMU2_PLL_PC0_P1DIV_MASK 0x00f00000
+#define PMU2_PLL_PC0_P1DIV_SHIFT 20
+#define PMU2_PLL_PC0_P2DIV_MASK 0x0f000000
+#define PMU2_PLL_PC0_P2DIV_SHIFT 24
+
+/* m<x>div */
+#define PMU2_PLL_PLLCTL1 1
+#define PMU2_PLL_PC1_M1DIV_MASK 0x000000ff
+#define PMU2_PLL_PC1_M1DIV_SHIFT 0
+#define PMU2_PLL_PC1_M2DIV_MASK 0x0000ff00
+#define PMU2_PLL_PC1_M2DIV_SHIFT 8
+#define PMU2_PLL_PC1_M3DIV_MASK 0x00ff0000
+#define PMU2_PLL_PC1_M3DIV_SHIFT 16
+#define PMU2_PLL_PC1_M4DIV_MASK 0xff000000
+#define PMU2_PLL_PC1_M4DIV_SHIFT 24
+
+/* m<x>div, ndiv_dither_mfb, ndiv_mode, ndiv_int */
+#define PMU2_PLL_PLLCTL2 2
+#define PMU2_PLL_PC2_M5DIV_MASK 0x000000ff
+#define PMU2_PLL_PC2_M5DIV_SHIFT 0
+#define PMU2_PLL_PC2_M6DIV_MASK 0x0000ff00
+#define PMU2_PLL_PC2_M6DIV_SHIFT 8
+#define PMU2_PLL_PC2_NDIV_MODE_MASK 0x000e0000
+#define PMU2_PLL_PC2_NDIV_MODE_SHIFT 17
+#define PMU2_PLL_PC2_NDIV_INT_MASK 0x1ff00000
+#define PMU2_PLL_PC2_NDIV_INT_SHIFT 20
+
+/* ndiv_frac */
+#define PMU2_PLL_PLLCTL3 3
+#define PMU2_PLL_PC3_NDIV_FRAC_MASK 0x00ffffff
+#define PMU2_PLL_PC3_NDIV_FRAC_SHIFT 0
+
+/* pll_ctrl */
+#define PMU2_PLL_PLLCTL4 4
+
+/* pll_ctrl, vco_rng, clkdrive_ch<x> */
+#define PMU2_PLL_PLLCTL5 5
+#define PMU2_PLL_PC5_CLKDRIVE_CH1_MASK 0x00000f00
+#define PMU2_PLL_PC5_CLKDRIVE_CH1_SHIFT 8
+#define PMU2_PLL_PC5_CLKDRIVE_CH2_MASK 0x0000f000
+#define PMU2_PLL_PC5_CLKDRIVE_CH2_SHIFT 12
+#define PMU2_PLL_PC5_CLKDRIVE_CH3_MASK 0x000f0000
+#define PMU2_PLL_PC5_CLKDRIVE_CH3_SHIFT 16
+#define PMU2_PLL_PC5_CLKDRIVE_CH4_MASK 0x00f00000
+#define PMU2_PLL_PC5_CLKDRIVE_CH4_SHIFT 20
+#define PMU2_PLL_PC5_CLKDRIVE_CH5_MASK 0x0f000000
+#define PMU2_PLL_PC5_CLKDRIVE_CH5_SHIFT 24
+#define PMU2_PLL_PC5_CLKDRIVE_CH6_MASK 0xf0000000
+#define PMU2_PLL_PC5_CLKDRIVE_CH6_SHIFT 28
+
+/* PMU rev 5 (& 6) */
+#define PMU5_PLL_P1P2_OFF 0
+#define PMU5_PLL_P1_MASK 0x0f000000
+#define PMU5_PLL_P1_SHIFT 24
+#define PMU5_PLL_P2_MASK 0x00f00000
+#define PMU5_PLL_P2_SHIFT 20
+#define PMU5_PLL_M14_OFF 1
+#define PMU5_PLL_MDIV_MASK 0x000000ff
+#define PMU5_PLL_MDIV_WIDTH 8
+#define PMU5_PLL_NM5_OFF 2
+#define PMU5_PLL_NDIV_MASK 0xfff00000
+#define PMU5_PLL_NDIV_SHIFT 20
+#define PMU5_PLL_NDIV_MODE_MASK 0x000e0000
+#define PMU5_PLL_NDIV_MODE_SHIFT 17
+#define PMU5_PLL_FMAB_OFF 3
+#define PMU5_PLL_MRAT_MASK 0xf0000000
+#define PMU5_PLL_MRAT_SHIFT 28
+#define PMU5_PLL_ABRAT_MASK 0x08000000
+#define PMU5_PLL_ABRAT_SHIFT 27
+#define PMU5_PLL_FDIV_MASK 0x07ffffff
+#define PMU5_PLL_PLLCTL_OFF 4
+#define PMU5_PLL_PCHI_OFF 5
+#define PMU5_PLL_PCHI_MASK 0x0000003f
+
+/* pmu XtalFreqRatio */
+#define PMU_XTALFREQ_REG_ILPCTR_MASK 0x00001FFF
+#define PMU_XTALFREQ_REG_MEASURE_MASK 0x80000000
+#define PMU_XTALFREQ_REG_MEASURE_SHIFT 31
+
+/* Divider allocation in 4716/47162/5356/5357 */
+#define PMU5_MAINPLL_CPU 1
+#define PMU5_MAINPLL_MEM 2
+#define PMU5_MAINPLL_SI 3
+
+#define PMU7_PLL_PLLCTL7 7
+#define PMU7_PLL_PLLCTL8 8
+#define PMU7_PLL_PLLCTL11 11
+
+/* PLL usage in 4716/47162 */
+#define PMU4716_MAINPLL_PLL0 12
+
+/* PLL usage in 5356/5357 */
+#define PMU5356_MAINPLL_PLL0 0
+#define PMU5357_MAINPLL_PLL0 0
+
+/* 4328 resources */
+#define RES4328_EXT_SWITCHER_PWM 0 /* 0x00001 */
+#define RES4328_BB_SWITCHER_PWM 1 /* 0x00002 */
+#define RES4328_BB_SWITCHER_BURST 2 /* 0x00004 */
+#define RES4328_BB_EXT_SWITCHER_BURST 3 /* 0x00008 */
+#define RES4328_ILP_REQUEST 4 /* 0x00010 */
+#define RES4328_RADIO_SWITCHER_PWM 5 /* 0x00020 */
+#define RES4328_RADIO_SWITCHER_BURST 6 /* 0x00040 */
+#define RES4328_ROM_SWITCH 7 /* 0x00080 */
+#define RES4328_PA_REF_LDO 8 /* 0x00100 */
+#define RES4328_RADIO_LDO 9 /* 0x00200 */
+#define RES4328_AFE_LDO 10 /* 0x00400 */
+#define RES4328_PLL_LDO 11 /* 0x00800 */
+#define RES4328_BG_FILTBYP 12 /* 0x01000 */
+#define RES4328_TX_FILTBYP 13 /* 0x02000 */
+#define RES4328_RX_FILTBYP 14 /* 0x04000 */
+#define RES4328_XTAL_PU 15 /* 0x08000 */
+#define RES4328_XTAL_EN 16 /* 0x10000 */
+#define RES4328_BB_PLL_FILTBYP 17 /* 0x20000 */
+#define RES4328_RF_PLL_FILTBYP 18 /* 0x40000 */
+#define RES4328_BB_PLL_PU 19 /* 0x80000 */
+
+/* 4325 A0/A1 resources */
+#define RES4325_BUCK_BOOST_BURST 0 /* 0x00000001 */
+#define RES4325_CBUCK_BURST 1 /* 0x00000002 */
+#define RES4325_CBUCK_PWM 2 /* 0x00000004 */
+#define RES4325_CLDO_CBUCK_BURST 3 /* 0x00000008 */
+#define RES4325_CLDO_CBUCK_PWM 4 /* 0x00000010 */
+#define RES4325_BUCK_BOOST_PWM 5 /* 0x00000020 */
+#define RES4325_ILP_REQUEST 6 /* 0x00000040 */
+#define RES4325_ABUCK_BURST 7 /* 0x00000080 */
+#define RES4325_ABUCK_PWM 8 /* 0x00000100 */
+#define RES4325_LNLDO1_PU 9 /* 0x00000200 */
+#define RES4325_OTP_PU 10 /* 0x00000400 */
+#define RES4325_LNLDO3_PU 11 /* 0x00000800 */
+#define RES4325_LNLDO4_PU 12 /* 0x00001000 */
+#define RES4325_XTAL_PU 13 /* 0x00002000 */
+#define RES4325_ALP_AVAIL 14 /* 0x00004000 */
+#define RES4325_RX_PWRSW_PU 15 /* 0x00008000 */
+#define RES4325_TX_PWRSW_PU 16 /* 0x00010000 */
+#define RES4325_RFPLL_PWRSW_PU 17 /* 0x00020000 */
+#define RES4325_LOGEN_PWRSW_PU 18 /* 0x00040000 */
+#define RES4325_AFE_PWRSW_PU 19 /* 0x00080000 */
+#define RES4325_BBPLL_PWRSW_PU 20 /* 0x00100000 */
+#define RES4325_HT_AVAIL 21 /* 0x00200000 */
+
+/* 4325 B0/C0 resources */
+#define RES4325B0_CBUCK_LPOM 1 /* 0x00000002 */
+#define RES4325B0_CBUCK_BURST 2 /* 0x00000004 */
+#define RES4325B0_CBUCK_PWM 3 /* 0x00000008 */
+#define RES4325B0_CLDO_PU 4 /* 0x00000010 */
+
+/* 4325 C1 resources */
+#define RES4325C1_LNLDO2_PU 12 /* 0x00001000 */
+
+#define RES4329_RESERVED0 0 /* 0x00000001 */
+#define RES4329_CBUCK_LPOM 1 /* 0x00000002 */
+#define RES4329_CBUCK_BURST 2 /* 0x00000004 */
+#define RES4329_CBUCK_PWM 3 /* 0x00000008 */
+#define RES4329_CLDO_PU 4 /* 0x00000010 */
+#define RES4329_PALDO_PU 5 /* 0x00000020 */
+#define RES4329_ILP_REQUEST 6 /* 0x00000040 */
+#define RES4329_RESERVED7 7 /* 0x00000080 */
+#define RES4329_RESERVED8 8 /* 0x00000100 */
+#define RES4329_LNLDO1_PU 9 /* 0x00000200 */
+#define RES4329_OTP_PU 10 /* 0x00000400 */
+#define RES4329_RESERVED11 11 /* 0x00000800 */
+#define RES4329_LNLDO2_PU 12 /* 0x00001000 */
+#define RES4329_XTAL_PU 13 /* 0x00002000 */
+#define RES4329_ALP_AVAIL 14 /* 0x00004000 */
+#define RES4329_RX_PWRSW_PU 15 /* 0x00008000 */
+#define RES4329_TX_PWRSW_PU 16 /* 0x00010000 */
+#define RES4329_RFPLL_PWRSW_PU 17 /* 0x00020000 */
+#define RES4329_LOGEN_PWRSW_PU 18 /* 0x00040000 */
+#define RES4329_AFE_PWRSW_PU 19 /* 0x00080000 */
+#define RES4329_BBPLL_PWRSW_PU 20 /* 0x00100000 */
+#define RES4329_HT_AVAIL 21 /* 0x00200000 */
+
+/* 4315 resources */
+#define RES4315_CBUCK_LPOM 1 /* 0x00000002 */
+#define RES4315_CBUCK_BURST 2 /* 0x00000004 */
+#define RES4315_CBUCK_PWM 3 /* 0x00000008 */
+#define RES4315_CLDO_PU 4 /* 0x00000010 */
+#define RES4315_PALDO_PU 5 /* 0x00000020 */
+#define RES4315_ILP_REQUEST 6 /* 0x00000040 */
+#define RES4315_LNLDO1_PU 9 /* 0x00000200 */
+#define RES4315_OTP_PU 10 /* 0x00000400 */
+#define RES4315_LNLDO2_PU 12 /* 0x00001000 */
+#define RES4315_XTAL_PU 13 /* 0x00002000 */
+#define RES4315_ALP_AVAIL 14 /* 0x00004000 */
+#define RES4315_RX_PWRSW_PU 15 /* 0x00008000 */
+#define RES4315_TX_PWRSW_PU 16 /* 0x00010000 */
+#define RES4315_RFPLL_PWRSW_PU 17 /* 0x00020000 */
+#define RES4315_LOGEN_PWRSW_PU 18 /* 0x00040000 */
+#define RES4315_AFE_PWRSW_PU 19 /* 0x00080000 */
+#define RES4315_BBPLL_PWRSW_PU 20 /* 0x00100000 */
+#define RES4315_HT_AVAIL 21 /* 0x00200000 */
+
+/* 4319 resources */
+#define RES4319_CBUCK_LPOM 1 /* 0x00000002 */
+#define RES4319_CBUCK_BURST 2 /* 0x00000004 */
+#define RES4319_CBUCK_PWM 3 /* 0x00000008 */
+#define RES4319_CLDO_PU 4 /* 0x00000010 */
+#define RES4319_PALDO_PU 5 /* 0x00000020 */
+#define RES4319_ILP_REQUEST 6 /* 0x00000040 */
+#define RES4319_LNLDO1_PU 9 /* 0x00000200 */
+#define RES4319_OTP_PU 10 /* 0x00000400 */
+#define RES4319_LNLDO2_PU 12 /* 0x00001000 */
+#define RES4319_XTAL_PU 13 /* 0x00002000 */
+#define RES4319_ALP_AVAIL 14 /* 0x00004000 */
+#define RES4319_RX_PWRSW_PU 15 /* 0x00008000 */
+#define RES4319_TX_PWRSW_PU 16 /* 0x00010000 */
+#define RES4319_RFPLL_PWRSW_PU 17 /* 0x00020000 */
+#define RES4319_LOGEN_PWRSW_PU 18 /* 0x00040000 */
+#define RES4319_AFE_PWRSW_PU 19 /* 0x00080000 */
+#define RES4319_BBPLL_PWRSW_PU 20 /* 0x00100000 */
+#define RES4319_HT_AVAIL 21 /* 0x00200000 */
+
+#define CCTL_4319USB_XTAL_SEL_MASK 0x00180000
+#define CCTL_4319USB_XTAL_SEL_SHIFT 19
+#define CCTL_4319USB_48MHZ_PLL_SEL 1
+#define CCTL_4319USB_24MHZ_PLL_SEL 2
+
+/* PMU resources for 4336 */
+#define RES4336_CBUCK_LPOM 0
+#define RES4336_CBUCK_BURST 1
+#define RES4336_CBUCK_LP_PWM 2
+#define RES4336_CBUCK_PWM 3
+#define RES4336_CLDO_PU 4
+#define RES4336_DIS_INT_RESET_PD 5
+#define RES4336_ILP_REQUEST 6
+#define RES4336_LNLDO_PU 7
+#define RES4336_LDO3P3_PU 8
+#define RES4336_OTP_PU 9
+#define RES4336_XTAL_PU 10
+#define RES4336_ALP_AVAIL 11
+#define RES4336_RADIO_PU 12
+#define RES4336_BG_PU 13
+#define RES4336_VREG1p4_PU_PU 14
+#define RES4336_AFE_PWRSW_PU 15
+#define RES4336_RX_PWRSW_PU 16
+#define RES4336_TX_PWRSW_PU 17
+#define RES4336_BB_PWRSW_PU 18
+#define RES4336_SYNTH_PWRSW_PU 19
+#define RES4336_MISC_PWRSW_PU 20
+#define RES4336_LOGEN_PWRSW_PU 21
+#define RES4336_BBPLL_PWRSW_PU 22
+#define RES4336_MACPHY_CLKAVAIL 23
+#define RES4336_HT_AVAIL 24
+#define RES4336_RSVD 25
+
+/* 4330 resources */
+#define RES4330_CBUCK_LPOM 0
+#define RES4330_CBUCK_BURST 1
+#define RES4330_CBUCK_LP_PWM 2
+#define RES4330_CBUCK_PWM 3
+#define RES4330_CLDO_PU 4
+#define RES4330_DIS_INT_RESET_PD 5
+#define RES4330_ILP_REQUEST 6
+#define RES4330_LNLDO_PU 7
+#define RES4330_LDO3P3_PU 8
+#define RES4330_OTP_PU 9
+#define RES4330_XTAL_PU 10
+#define RES4330_ALP_AVAIL 11
+#define RES4330_RADIO_PU 12
+#define RES4330_BG_PU 13
+#define RES4330_VREG1p4_PU_PU 14
+#define RES4330_AFE_PWRSW_PU 15
+#define RES4330_RX_PWRSW_PU 16
+#define RES4330_TX_PWRSW_PU 17
+#define RES4330_BB_PWRSW_PU 18
+#define RES4330_SYNTH_PWRSW_PU 19
+#define RES4330_MISC_PWRSW_PU 20
+#define RES4330_LOGEN_PWRSW_PU 21
+#define RES4330_BBPLL_PWRSW_PU 22
+#define RES4330_MACPHY_CLKAVAIL 23
+#define RES4330_HT_AVAIL 24
+#define RES4330_5gRX_PWRSW_PU 25
+#define RES4330_5gTX_PWRSW_PU 26
+#define RES4330_5g_LOGEN_PWRSW_PU 27
+
+/* 4313 resources */
+#define RES4313_BB_PU_RSRC 0
+#define RES4313_ILP_REQ_RSRC 1
+#define RES4313_XTAL_PU_RSRC 2
+#define RES4313_ALP_AVAIL_RSRC 3
+#define RES4313_RADIO_PU_RSRC 4
+#define RES4313_BG_PU_RSRC 5
+#define RES4313_VREG1P4_PU_RSRC 6
+#define RES4313_AFE_PWRSW_RSRC 7
+#define RES4313_RX_PWRSW_RSRC 8
+#define RES4313_TX_PWRSW_RSRC 9
+#define RES4313_BB_PWRSW_RSRC 10
+#define RES4313_SYNTH_PWRSW_RSRC 11
+#define RES4313_MISC_PWRSW_RSRC 12
+#define RES4313_BB_PLL_PWRSW_RSRC 13
+#define RES4313_HT_AVAIL_RSRC 14
+#define RES4313_MACPHY_CLK_AVAIL_RSRC 15
+
+/* PMU resource up transition time in ILP cycles */
+#define PMURES_UP_TRANSITION 2
+
/* Setup resource up/down timers */
typedef struct {
u8 resnum;
#ifndef _SBCHIPC_H
#define _SBCHIPC_H
-#ifndef _LANGUAGE_ASSEMBLY
-
/* cpp contortions to concatenate w/arg prescan */
#ifndef PAD
#define _PADLINE(line) pad ## line
u16 sromotp[768];
} chipcregs_t;
-#endif /* _LANGUAGE_ASSEMBLY */
-
-#if defined(__BIG_ENDIAN) && defined(BCMHND74K)
-/* Selective swapped defines for those registers we need in
- * big-endian code.
- */
-#define CC_CHIPID 4
-#define CC_CAPABILITIES 0
-#define CC_CHIPST 0x28
-#define CC_EROMPTR 0xf8
-
-#else /* !__BIG_ENDIAN || !BCMHND74K */
-
-#define CC_CHIPID 0
-#define CC_CAPABILITIES 4
-#define CC_CHIPST 0x2c
-#define CC_EROMPTR 0xfc
-
-#endif /* __BIG_ENDIAN && BCMHND74K */
-
-#define CC_OTPST 0x10
-#define CC_JTAGCMD 0x30
-#define CC_JTAGIR 0x34
-#define CC_JTAGDR 0x38
-#define CC_JTAGCTRL 0x3c
-#define CC_GPIOPU 0x58
-#define CC_GPIOPD 0x5c
-#define CC_GPIOIN 0x60
-#define CC_GPIOOUT 0x64
-#define CC_GPIOOUTEN 0x68
-#define CC_GPIOCTRL 0x6c
-#define CC_GPIOPOL 0x70
-#define CC_GPIOINTM 0x74
-#define CC_WATCHDOG 0x80
-#define CC_CLKC_N 0x90
-#define CC_CLKC_M0 0x94
-#define CC_CLKC_M1 0x98
-#define CC_CLKC_M2 0x9c
-#define CC_CLKC_M3 0xa0
-#define CC_CLKDIV 0xa4
-#define CC_SYS_CLK_CTL 0xc0
-#define CC_CLK_CTL_ST SI_CLK_CTL_ST
-#define PMU_CTL 0x600
-#define PMU_CAP 0x604
-#define PMU_ST 0x608
-#define PMU_RES_STATE 0x60c
-#define PMU_TIMER 0x614
-#define PMU_MIN_RES_MASK 0x618
-#define PMU_MAX_RES_MASK 0x61c
-#define CC_CHIPCTL_ADDR 0x650
-#define CC_CHIPCTL_DATA 0x654
-#define PMU_REG_CONTROL_ADDR 0x658
-#define PMU_REG_CONTROL_DATA 0x65C
-#define PMU_PLL_CONTROL_ADDR 0x660
-#define PMU_PLL_CONTROL_DATA 0x664
-#define CC_SROM_OTP 0x800 /* SROM/OTP address space */
-
/* chipid */
#define CID_ID_MASK 0x0000ffff /* Chip Id mask */
#define CID_REV_MASK 0x000f0000 /* Chip Revision mask */
#define CC_CAP2_SECI 0x00000001 /* SECI Present, rev >= 36 */
#define CC_CAP2_GSIO 0x00000002 /* GSIO (spi/i2c) present, rev >= 37 */
-/* PLL type */
-#define PLL_NONE 0x00000000
-#define PLL_TYPE1 0x00010000 /* 48MHz base, 3 dividers */
-#define PLL_TYPE2 0x00020000 /* 48MHz, 4 dividers */
-#define PLL_TYPE3 0x00030000 /* 25MHz, 2 dividers */
-#define PLL_TYPE4 0x00008000 /* 48MHz, 4 dividers */
-#define PLL_TYPE5 0x00018000 /* 25MHz, 4 dividers */
-#define PLL_TYPE6 0x00028000 /* 100/200 or 120/240 only */
-#define PLL_TYPE7 0x00038000 /* 25MHz, 4 dividers */
-
-/* ILP clock */
-#define ILP_CLOCK 32000
-
-/* ALP clock on pre-PMU chips */
-#define ALP_CLOCK 20000000
-
-/* HT clock */
-#define HT_CLOCK 80000000
-
-/* corecontrol */
-#define CC_UARTCLKO 0x00000001 /* Drive UART with internal clock */
-#define CC_SE 0x00000002 /* sync clk out enable (corerev >= 3) */
-#define CC_UARTCLKEN 0x00000008 /* enable UART Clock (corerev > = 21 */
-
-/* chipcontrol */
-#define CHIPCTRL_4321A0_DEFAULT 0x3a4
-#define CHIPCTRL_4321A1_DEFAULT 0x0a4
-#define CHIPCTRL_4321_PLL_DOWN 0x800000 /* serdes PLL down override */
-
-/* Fields in the otpstatus register in rev >= 21 */
-#define OTPS_OL_MASK 0x000000ff
-#define OTPS_OL_MFG 0x00000001 /* manuf row is locked */
-#define OTPS_OL_OR1 0x00000002 /* otp redundancy row 1 is locked */
-#define OTPS_OL_OR2 0x00000004 /* otp redundancy row 2 is locked */
-#define OTPS_OL_GU 0x00000008 /* general use region is locked */
-#define OTPS_GUP_MASK 0x00000f00
-#define OTPS_GUP_SHIFT 8
-#define OTPS_GUP_HW 0x00000100 /* h/w subregion is programmed */
-#define OTPS_GUP_SW 0x00000200 /* s/w subregion is programmed */
-#define OTPS_GUP_CI 0x00000400 /* chipid/pkgopt subregion is programmed */
-#define OTPS_GUP_FUSE 0x00000800 /* fuse subregion is programmed */
-#define OTPS_READY 0x00001000
-#define OTPS_RV(x) (1 << (16 + (x))) /* redundancy entry valid */
-#define OTPS_RV_MASK 0x0fff0000
-
-/* Fields in the otpcontrol register in rev >= 21 */
-#define OTPC_PROGSEL 0x00000001
-#define OTPC_PCOUNT_MASK 0x0000000e
-#define OTPC_PCOUNT_SHIFT 1
-#define OTPC_VSEL_MASK 0x000000f0
-#define OTPC_VSEL_SHIFT 4
-#define OTPC_TMM_MASK 0x00000700
-#define OTPC_TMM_SHIFT 8
-#define OTPC_ODM 0x00000800
-#define OTPC_PROGEN 0x80000000
-
-/* Fields in otpprog in rev >= 21 and HND OTP */
-#define OTPP_COL_MASK 0x000000ff
-#define OTPP_COL_SHIFT 0
-#define OTPP_ROW_MASK 0x0000ff00
-#define OTPP_ROW_SHIFT 8
-#define OTPP_OC_MASK 0x0f000000
-#define OTPP_OC_SHIFT 24
-#define OTPP_READERR 0x10000000
-#define OTPP_VALUE_MASK 0x20000000
-#define OTPP_VALUE_SHIFT 29
-#define OTPP_START_BUSY 0x80000000
-#define OTPP_READ 0x40000000 /* HND OTP */
-
-/* otplayout reg corerev >= 36 */
-#define OTP_CISFORMAT_NEW 0x80000000
-
-/* Opcodes for OTPP_OC field */
-#define OTPPOC_READ 0
-#define OTPPOC_BIT_PROG 1
-#define OTPPOC_VERIFY 3
-#define OTPPOC_INIT 4
-#define OTPPOC_SET 5
-#define OTPPOC_RESET 6
-#define OTPPOC_OCST 7
-#define OTPPOC_ROW_LOCK 8
-#define OTPPOC_PRESCN_TEST 9
-
-/* Jtagm characteristics that appeared at a given corerev */
-#define JTAGM_CREV_OLD 10 /* Old command set, 16bit max IR */
-#define JTAGM_CREV_IRP 22 /* Able to do pause-ir */
-#define JTAGM_CREV_RTI 28 /* Able to do return-to-idle */
-
-/* jtagcmd */
-#define JCMD_START 0x80000000
-#define JCMD_BUSY 0x80000000
-#define JCMD_STATE_MASK 0x60000000
-#define JCMD_STATE_TLR 0x00000000 /* Test-logic-reset */
-#define JCMD_STATE_PIR 0x20000000 /* Pause IR */
-#define JCMD_STATE_PDR 0x40000000 /* Pause DR */
-#define JCMD_STATE_RTI 0x60000000 /* Run-test-idle */
-#define JCMD0_ACC_MASK 0x0000f000
-#define JCMD0_ACC_IRDR 0x00000000
-#define JCMD0_ACC_DR 0x00001000
-#define JCMD0_ACC_IR 0x00002000
-#define JCMD0_ACC_RESET 0x00003000
-#define JCMD0_ACC_IRPDR 0x00004000
-#define JCMD0_ACC_PDR 0x00005000
-#define JCMD0_IRW_MASK 0x00000f00
-#define JCMD_ACC_MASK 0x000f0000 /* Changes for corerev 11 */
-#define JCMD_ACC_IRDR 0x00000000
-#define JCMD_ACC_DR 0x00010000
-#define JCMD_ACC_IR 0x00020000
-#define JCMD_ACC_RESET 0x00030000
-#define JCMD_ACC_IRPDR 0x00040000
-#define JCMD_ACC_PDR 0x00050000
-#define JCMD_ACC_PIR 0x00060000
-#define JCMD_ACC_IRDR_I 0x00070000 /* rev 28: return to run-test-idle */
-#define JCMD_ACC_DR_I 0x00080000 /* rev 28: return to run-test-idle */
-#define JCMD_IRW_MASK 0x00001f00
-#define JCMD_IRW_SHIFT 8
-#define JCMD_DRW_MASK 0x0000003f
-
-/* jtagctrl */
-#define JCTRL_FORCE_CLK 4 /* Force clock */
-#define JCTRL_EXT_EN 2 /* Enable external targets */
-#define JCTRL_EN 1 /* Enable Jtag master */
-
-/* Fields in clkdiv */
-#define CLKD_SFLASH 0x0f000000
-#define CLKD_SFLASH_SHIFT 24
-#define CLKD_OTP 0x000f0000
-#define CLKD_OTP_SHIFT 16
-#define CLKD_JTAG 0x00000f00
-#define CLKD_JTAG_SHIFT 8
-#define CLKD_UART 0x000000ff
-
-#define CLKD2_SROM 0x00000003
-
-/* intstatus/intmask */
-#define CI_GPIO 0x00000001 /* gpio intr */
-#define CI_EI 0x00000002 /* extif intr (corerev >= 3) */
-#define CI_TEMP 0x00000004 /* temp. ctrl intr (corerev >= 15) */
-#define CI_SIRQ 0x00000008 /* serial IRQ intr (corerev >= 15) */
-#define CI_PMU 0x00000020 /* pmu intr (corerev >= 21) */
-#define CI_UART 0x00000040 /* uart intr (corerev >= 21) */
-#define CI_WDRESET 0x80000000 /* watchdog reset occurred */
-
-/* slow_clk_ctl */
-#define SCC_SS_MASK 0x00000007 /* slow clock source mask */
-#define SCC_SS_LPO 0x00000000 /* source of slow clock is LPO */
-#define SCC_SS_XTAL 0x00000001 /* source of slow clock is crystal */
-#define SCC_SS_PCI 0x00000002 /* source of slow clock is PCI */
-#define SCC_LF 0x00000200 /* LPOFreqSel, 1: 160Khz, 0: 32KHz */
-#define SCC_LP 0x00000400 /* LPOPowerDown, 1: LPO is disabled,
- * 0: LPO is enabled
- */
-#define SCC_FS 0x00000800 /* ForceSlowClk, 1: sb/cores running on slow clock,
- * 0: power logic control
- */
-#define SCC_IP 0x00001000 /* IgnorePllOffReq, 1/0: power logic ignores/honors
- * PLL clock disable requests from core
- */
-#define SCC_XC 0x00002000 /* XtalControlEn, 1/0: power logic does/doesn't
- * disable crystal when appropriate
- */
-#define SCC_XP 0x00004000 /* XtalPU (RO), 1/0: crystal running/disabled */
-#define SCC_CD_MASK 0xffff0000 /* ClockDivider (SlowClk = 1/(4+divisor)) */
-#define SCC_CD_SHIFT 16
-
-/* system_clk_ctl */
-#define SYCC_IE 0x00000001 /* ILPen: Enable Idle Low Power */
-#define SYCC_AE 0x00000002 /* ALPen: Enable Active Low Power */
-#define SYCC_FP 0x00000004 /* ForcePLLOn */
-#define SYCC_AR 0x00000008 /* Force ALP (or HT if ALPen is not set */
-#define SYCC_HR 0x00000010 /* Force HT */
-#define SYCC_CD_MASK 0xffff0000 /* ClkDiv (ILP = 1/(4 * (divisor + 1)) */
-#define SYCC_CD_SHIFT 16
-
-/* Indirect backplane access */
-#define BPIA_BYTEEN 0x0000000f
-#define BPIA_SZ1 0x00000001
-#define BPIA_SZ2 0x00000003
-#define BPIA_SZ4 0x00000007
-#define BPIA_SZ8 0x0000000f
-#define BPIA_WRITE 0x00000100
-#define BPIA_START 0x00000200
-#define BPIA_BUSY 0x00000200
-#define BPIA_ERROR 0x00000400
-
-/* pcmcia/prog/flash_config */
-#define CF_EN 0x00000001 /* enable */
-#define CF_EM_MASK 0x0000000e /* mode */
-#define CF_EM_SHIFT 1
-#define CF_EM_FLASH 0 /* flash/asynchronous mode */
-#define CF_EM_SYNC 2 /* synchronous mode */
-#define CF_EM_PCMCIA 4 /* pcmcia mode */
-#define CF_DS 0x00000010 /* destsize: 0=8bit, 1=16bit */
-#define CF_BS 0x00000020 /* byteswap */
-#define CF_CD_MASK 0x000000c0 /* clock divider */
-#define CF_CD_SHIFT 6
-#define CF_CD_DIV2 0x00000000 /* backplane/2 */
-#define CF_CD_DIV3 0x00000040 /* backplane/3 */
-#define CF_CD_DIV4 0x00000080 /* backplane/4 */
-#define CF_CE 0x00000100 /* clock enable */
-#define CF_SB 0x00000200 /* size/bytestrobe (synch only) */
-
-/* pcmcia_memwait */
-#define PM_W0_MASK 0x0000003f /* waitcount0 */
-#define PM_W1_MASK 0x00001f00 /* waitcount1 */
-#define PM_W1_SHIFT 8
-#define PM_W2_MASK 0x001f0000 /* waitcount2 */
-#define PM_W2_SHIFT 16
-#define PM_W3_MASK 0x1f000000 /* waitcount3 */
-#define PM_W3_SHIFT 24
-
-/* pcmcia_attrwait */
-#define PA_W0_MASK 0x0000003f /* waitcount0 */
-#define PA_W1_MASK 0x00001f00 /* waitcount1 */
-#define PA_W1_SHIFT 8
-#define PA_W2_MASK 0x001f0000 /* waitcount2 */
-#define PA_W2_SHIFT 16
-#define PA_W3_MASK 0x1f000000 /* waitcount3 */
-#define PA_W3_SHIFT 24
-
-/* pcmcia_iowait */
-#define PI_W0_MASK 0x0000003f /* waitcount0 */
-#define PI_W1_MASK 0x00001f00 /* waitcount1 */
-#define PI_W1_SHIFT 8
-#define PI_W2_MASK 0x001f0000 /* waitcount2 */
-#define PI_W2_SHIFT 16
-#define PI_W3_MASK 0x1f000000 /* waitcount3 */
-#define PI_W3_SHIFT 24
-
-/* prog_waitcount */
-#define PW_W0_MASK 0x0000001f /* waitcount0 */
-#define PW_W1_MASK 0x00001f00 /* waitcount1 */
-#define PW_W1_SHIFT 8
-#define PW_W2_MASK 0x001f0000 /* waitcount2 */
-#define PW_W2_SHIFT 16
-#define PW_W3_MASK 0x1f000000 /* waitcount3 */
-#define PW_W3_SHIFT 24
-
-#define PW_W0 0x0000000c
-#define PW_W1 0x00000a00
-#define PW_W2 0x00020000
-#define PW_W3 0x01000000
-
-/* flash_waitcount */
-#define FW_W0_MASK 0x0000003f /* waitcount0 */
-#define FW_W1_MASK 0x00001f00 /* waitcount1 */
-#define FW_W1_SHIFT 8
-#define FW_W2_MASK 0x001f0000 /* waitcount2 */
-#define FW_W2_SHIFT 16
-#define FW_W3_MASK 0x1f000000 /* waitcount3 */
-#define FW_W3_SHIFT 24
-
-/* When Srom support present, fields in sromcontrol */
-#define SRC_START 0x80000000
-#define SRC_BUSY 0x80000000
-#define SRC_OPCODE 0x60000000
-#define SRC_OP_READ 0x00000000
-#define SRC_OP_WRITE 0x20000000
-#define SRC_OP_WRDIS 0x40000000
-#define SRC_OP_WREN 0x60000000
-#define SRC_OTPSEL 0x00000010
-#define SRC_LOCK 0x00000008
-#define SRC_SIZE_MASK 0x00000006
-#define SRC_SIZE_1K 0x00000000
-#define SRC_SIZE_4K 0x00000002
-#define SRC_SIZE_16K 0x00000004
-#define SRC_SIZE_SHIFT 1
-#define SRC_PRESENT 0x00000001
-
-/* Fields in pmucontrol */
-#define PCTL_ILP_DIV_MASK 0xffff0000
-#define PCTL_ILP_DIV_SHIFT 16
-#define PCTL_PLL_PLLCTL_UPD 0x00000400 /* rev 2 */
-#define PCTL_NOILP_ON_WAIT 0x00000200 /* rev 1 */
-#define PCTL_HT_REQ_EN 0x00000100
-#define PCTL_ALP_REQ_EN 0x00000080
-#define PCTL_XTALFREQ_MASK 0x0000007c
-#define PCTL_XTALFREQ_SHIFT 2
-#define PCTL_ILP_DIV_EN 0x00000002
-#define PCTL_LPO_SEL 0x00000001
-
-/* Fields in clkstretch */
-#define CSTRETCH_HT 0xffff0000
-#define CSTRETCH_ALP 0x0000ffff
-
-/* gpiotimerval */
-#define GPIO_ONTIME_SHIFT 16
-
-/* clockcontrol_n */
-#define CN_N1_MASK 0x3f /* n1 control */
-#define CN_N2_MASK 0x3f00 /* n2 control */
-#define CN_N2_SHIFT 8
-#define CN_PLLC_MASK 0xf0000 /* pll control */
-#define CN_PLLC_SHIFT 16
-
-/* clockcontrol_sb/pci/uart */
-#define CC_M1_MASK 0x3f /* m1 control */
-#define CC_M2_MASK 0x3f00 /* m2 control */
-#define CC_M2_SHIFT 8
-#define CC_M3_MASK 0x3f0000 /* m3 control */
-#define CC_M3_SHIFT 16
-#define CC_MC_MASK 0x1f000000 /* mux control */
-#define CC_MC_SHIFT 24
-
-/* N3M Clock control magic field values */
-#define CC_F6_2 0x02 /* A factor of 2 in */
-#define CC_F6_3 0x03 /* 6-bit fields like */
-#define CC_F6_4 0x05 /* N1, M1 or M3 */
-#define CC_F6_5 0x09
-#define CC_F6_6 0x11
-#define CC_F6_7 0x21
-
-#define CC_F5_BIAS 5 /* 5-bit fields get this added */
-
-#define CC_MC_BYPASS 0x08
-#define CC_MC_M1 0x04
-#define CC_MC_M1M2 0x02
-#define CC_MC_M1M2M3 0x01
-#define CC_MC_M1M3 0x11
-
-/* Type 2 Clock control magic field values */
-#define CC_T2_BIAS 2 /* n1, n2, m1 & m3 bias */
-#define CC_T2M2_BIAS 3 /* m2 bias */
-
-#define CC_T2MC_M1BYP 1
-#define CC_T2MC_M2BYP 2
-#define CC_T2MC_M3BYP 4
-
-/* Type 6 Clock control magic field values */
-#define CC_T6_MMASK 1 /* bits of interest in m */
-#define CC_T6_M0 120000000 /* sb clock for m = 0 */
-#define CC_T6_M1 100000000 /* sb clock for m = 1 */
-#define SB2MIPS_T6(sb) (2 * (sb))
-
-/* Common clock base */
-#define CC_CLOCK_BASE1 24000000 /* Half the clock freq */
-#define CC_CLOCK_BASE2 12500000 /* Alternate crystal on some PLLs */
-
-/* Clock control values for 200MHz in 5350 */
-#define CLKC_5350_N 0x0311
-#define CLKC_5350_M 0x04020009
-
-/* Flash types in the chipcommon capabilities register */
-#define FLASH_NONE 0x000 /* No flash */
-#define SFLASH_ST 0x100 /* ST serial flash */
-#define SFLASH_AT 0x200 /* Atmel serial flash */
-#define PFLASH 0x700 /* Parallel flash */
-
-/* Bits in the ExtBus config registers */
-#define CC_CFG_EN 0x0001 /* Enable */
-#define CC_CFG_EM_MASK 0x000e /* Extif Mode */
-#define CC_CFG_EM_ASYNC 0x0000 /* Async/Parallel flash */
-#define CC_CFG_EM_SYNC 0x0002 /* Synchronous */
-#define CC_CFG_EM_PCMCIA 0x0004 /* PCMCIA */
-#define CC_CFG_EM_IDE 0x0006 /* IDE */
-#define CC_CFG_DS 0x0010 /* Data size, 0=8bit, 1=16bit */
-#define CC_CFG_CD_MASK 0x00e0 /* Sync: Clock divisor, rev >= 20 */
-#define CC_CFG_CE 0x0100 /* Sync: Clock enable, rev >= 20 */
-#define CC_CFG_SB 0x0200 /* Sync: Size/Bytestrobe, rev >= 20 */
-#define CC_CFG_IS 0x0400 /* Extif Sync Clk Select, rev >= 20 */
-
-/* ExtBus address space */
-#define CC_EB_BASE 0x1a000000 /* Chipc ExtBus base address */
-#define CC_EB_PCMCIA_MEM 0x1a000000 /* PCMCIA 0 memory base address */
-#define CC_EB_PCMCIA_IO 0x1a200000 /* PCMCIA 0 I/O base address */
-#define CC_EB_PCMCIA_CFG 0x1a400000 /* PCMCIA 0 config base address */
-#define CC_EB_IDE 0x1a800000 /* IDE memory base */
-#define CC_EB_PCMCIA1_MEM 0x1a800000 /* PCMCIA 1 memory base address */
-#define CC_EB_PCMCIA1_IO 0x1aa00000 /* PCMCIA 1 I/O base address */
-#define CC_EB_PCMCIA1_CFG 0x1ac00000 /* PCMCIA 1 config base address */
-#define CC_EB_PROGIF 0x1b000000 /* ProgIF Async/Sync base address */
-
-/* Start/busy bit in flashcontrol */
-#define SFLASH_OPCODE 0x000000ff
-#define SFLASH_ACTION 0x00000700
-#define SFLASH_CS_ACTIVE 0x00001000 /* Chip Select Active, rev >= 20 */
-#define SFLASH_START 0x80000000
-#define SFLASH_BUSY SFLASH_START
-
-/* flashcontrol action codes */
-#define SFLASH_ACT_OPONLY 0x0000 /* Issue opcode only */
-#define SFLASH_ACT_OP1D 0x0100 /* opcode + 1 data byte */
-#define SFLASH_ACT_OP3A 0x0200 /* opcode + 3 addr bytes */
-#define SFLASH_ACT_OP3A1D 0x0300 /* opcode + 3 addr & 1 data bytes */
-#define SFLASH_ACT_OP3A4D 0x0400 /* opcode + 3 addr & 4 data bytes */
-#define SFLASH_ACT_OP3A4X4D 0x0500 /* opcode + 3 addr, 4 don't care & 4 data bytes */
-#define SFLASH_ACT_OP3A1X4D 0x0700 /* opcode + 3 addr, 1 don't care & 4 data bytes */
-
-/* flashcontrol action+opcodes for ST flashes */
-#define SFLASH_ST_WREN 0x0006 /* Write Enable */
-#define SFLASH_ST_WRDIS 0x0004 /* Write Disable */
-#define SFLASH_ST_RDSR 0x0105 /* Read Status Register */
-#define SFLASH_ST_WRSR 0x0101 /* Write Status Register */
-#define SFLASH_ST_READ 0x0303 /* Read Data Bytes */
-#define SFLASH_ST_PP 0x0302 /* Page Program */
-#define SFLASH_ST_SE 0x02d8 /* Sector Erase */
-#define SFLASH_ST_BE 0x00c7 /* Bulk Erase */
-#define SFLASH_ST_DP 0x00b9 /* Deep Power-down */
-#define SFLASH_ST_RES 0x03ab /* Read Electronic Signature */
-#define SFLASH_ST_CSA 0x1000 /* Keep chip select asserted */
-#define SFLASH_ST_SSE 0x0220 /* Sub-sector Erase */
-
-/* Status register bits for ST flashes */
-#define SFLASH_ST_WIP 0x01 /* Write In Progress */
-#define SFLASH_ST_WEL 0x02 /* Write Enable Latch */
-#define SFLASH_ST_BP_MASK 0x1c /* Block Protect */
-#define SFLASH_ST_BP_SHIFT 2
-#define SFLASH_ST_SRWD 0x80 /* Status Register Write Disable */
-
-/* flashcontrol action+opcodes for Atmel flashes */
-#define SFLASH_AT_READ 0x07e8
-#define SFLASH_AT_PAGE_READ 0x07d2
-#define SFLASH_AT_BUF1_READ
-#define SFLASH_AT_BUF2_READ
-#define SFLASH_AT_STATUS 0x01d7
-#define SFLASH_AT_BUF1_WRITE 0x0384
-#define SFLASH_AT_BUF2_WRITE 0x0387
-#define SFLASH_AT_BUF1_ERASE_PROGRAM 0x0283
-#define SFLASH_AT_BUF2_ERASE_PROGRAM 0x0286
-#define SFLASH_AT_BUF1_PROGRAM 0x0288
-#define SFLASH_AT_BUF2_PROGRAM 0x0289
-#define SFLASH_AT_PAGE_ERASE 0x0281
-#define SFLASH_AT_BLOCK_ERASE 0x0250
-#define SFLASH_AT_BUF1_WRITE_ERASE_PROGRAM 0x0382
-#define SFLASH_AT_BUF2_WRITE_ERASE_PROGRAM 0x0385
-#define SFLASH_AT_BUF1_LOAD 0x0253
-#define SFLASH_AT_BUF2_LOAD 0x0255
-#define SFLASH_AT_BUF1_COMPARE 0x0260
-#define SFLASH_AT_BUF2_COMPARE 0x0261
-#define SFLASH_AT_BUF1_REPROGRAM 0x0258
-#define SFLASH_AT_BUF2_REPROGRAM 0x0259
-
-/* Status register bits for Atmel flashes */
-#define SFLASH_AT_READY 0x80
-#define SFLASH_AT_MISMATCH 0x40
-#define SFLASH_AT_ID_MASK 0x38
-#define SFLASH_AT_ID_SHIFT 3
-
-/*
- * These are the UART port assignments, expressed as offsets from the base
- * register. These assignments should hold for any serial port based on
- * a 8250, 16450, or 16550(A).
- */
-
-#define UART_RX 0 /* In: Receive buffer (DLAB=0) */
-#define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */
-#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */
-#define UART_IER 1 /* In/Out: Interrupt Enable Register (DLAB=0) */
-#define UART_DLM 1 /* Out: Divisor Latch High (DLAB=1) */
-#define UART_IIR 2 /* In: Interrupt Identity Register */
-#define UART_FCR 2 /* Out: FIFO Control Register */
-#define UART_LCR 3 /* Out: Line Control Register */
-#define UART_MCR 4 /* Out: Modem Control Register */
-#define UART_LSR 5 /* In: Line Status Register */
-#define UART_MSR 6 /* In: Modem Status Register */
-#define UART_SCR 7 /* I/O: Scratch Register */
-#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
-#define UART_LCR_WLEN8 0x03 /* Word length: 8 bits */
-#define UART_MCR_OUT2 0x08 /* MCR GPIO out 2 */
-#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
-#define UART_LSR_RX_FIFO 0x80 /* Receive FIFO error */
-#define UART_LSR_TDHR 0x40 /* Data-hold-register empty */
-#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */
-#define UART_LSR_BREAK 0x10 /* Break interrupt */
-#define UART_LSR_FRAMING 0x08 /* Framing error */
-#define UART_LSR_PARITY 0x04 /* Parity error */
-#define UART_LSR_OVERRUN 0x02 /* Overrun error */
-#define UART_LSR_RXRDY 0x01 /* Receiver ready */
-#define UART_FCR_FIFO_ENABLE 1 /* FIFO control register bit controlling FIFO enable/disable */
-
-/* Interrupt Identity Register (IIR) bits */
-#define UART_IIR_FIFO_MASK 0xc0 /* IIR FIFO disable/enabled mask */
-#define UART_IIR_INT_MASK 0xf /* IIR interrupt ID source */
-#define UART_IIR_MDM_CHG 0x0 /* Modem status changed */
-#define UART_IIR_NOINT 0x1 /* No interrupt pending */
-#define UART_IIR_THRE 0x2 /* THR empty */
-#define UART_IIR_RCVD_DATA 0x4 /* Received data available */
-#define UART_IIR_RCVR_STATUS 0x6 /* Receiver status */
-#define UART_IIR_CHAR_TIME 0xc /* Character time */
-
-/* Interrupt Enable Register (IER) bits */
-#define UART_IER_EDSSI 8 /* enable modem status interrupt */
-#define UART_IER_ELSI 4 /* enable receiver line status interrupt */
-#define UART_IER_ETBEI 2 /* enable transmitter holding register empty interrupt */
-#define UART_IER_ERBFI 1 /* enable data available interrupt */
-
-/* pmustatus */
-#define PST_EXTLPOAVAIL 0x0100
-#define PST_WDRESET 0x0080
-#define PST_INTPEND 0x0040
-#define PST_SBCLKST 0x0030
-#define PST_SBCLKST_ILP 0x0010
-#define PST_SBCLKST_ALP 0x0020
-#define PST_SBCLKST_HT 0x0030
-#define PST_ALPAVAIL 0x0008
-#define PST_HTAVAIL 0x0004
-#define PST_RESINIT 0x0003
-
/* pmucapabilities */
#define PCAP_REV_MASK 0x000000ff
#define PCAP_RC_MASK 0x00001f00
#define PCAP5_CC_MASK 0xf8000000
#define PCAP5_CC_SHIFT 27
-/* PMU Resource Request Timer registers */
-/* This is based on PmuRev0 */
-#define PRRT_TIME_MASK 0x03ff
-#define PRRT_INTEN 0x0400
-#define PRRT_REQ_ACTIVE 0x0800
-#define PRRT_ALP_REQ 0x1000
-#define PRRT_HT_REQ 0x2000
-
-/* PMU resource bit position */
-#define PMURES_BIT(bit) (1 << (bit))
-
-/* PMU resource number limit */
-#define PMURES_MAX_RESNUM 30
-
-/* PMU chip control0 register */
-#define PMU_CHIPCTL0 0
-
-/* PMU chip control1 register */
-#define PMU_CHIPCTL1 1
-#define PMU_CC1_RXC_DLL_BYPASS 0x00010000
-
-#define PMU_CC1_IF_TYPE_MASK 0x00000030
-#define PMU_CC1_IF_TYPE_RMII 0x00000000
-#define PMU_CC1_IF_TYPE_MII 0x00000010
-#define PMU_CC1_IF_TYPE_RGMII 0x00000020
-
-#define PMU_CC1_SW_TYPE_MASK 0x000000c0
-#define PMU_CC1_SW_TYPE_EPHY 0x00000000
-#define PMU_CC1_SW_TYPE_EPHYMII 0x00000040
-#define PMU_CC1_SW_TYPE_EPHYRMII 0x00000080
-#define PMU_CC1_SW_TYPE_RGMII 0x000000c0
-
-/* PMU corerev and chip specific PLL controls.
- * PMU<rev>_PLL<num>_XX where <rev> is PMU corerev and <num> is an arbitrary number
- * to differentiate different PLLs controlled by the same PMU rev.
- */
-/* pllcontrol registers */
-/* PDIV, div_phy, div_arm, div_adc, dith_sel, ioff, kpd_scale, lsb_sel, mash_sel, lf_c & lf_r */
-#define PMU0_PLL0_PLLCTL0 0
-#define PMU0_PLL0_PC0_PDIV_MASK 1
-#define PMU0_PLL0_PC0_PDIV_FREQ 25000
-#define PMU0_PLL0_PC0_DIV_ARM_MASK 0x00000038
-#define PMU0_PLL0_PC0_DIV_ARM_SHIFT 3
-#define PMU0_PLL0_PC0_DIV_ARM_BASE 8
-
-/* PC0_DIV_ARM for PLLOUT_ARM */
-#define PMU0_PLL0_PC0_DIV_ARM_110MHZ 0
-#define PMU0_PLL0_PC0_DIV_ARM_97_7MHZ 1
-#define PMU0_PLL0_PC0_DIV_ARM_88MHZ 2
-#define PMU0_PLL0_PC0_DIV_ARM_80MHZ 3 /* Default */
-#define PMU0_PLL0_PC0_DIV_ARM_73_3MHZ 4
-#define PMU0_PLL0_PC0_DIV_ARM_67_7MHZ 5
-#define PMU0_PLL0_PC0_DIV_ARM_62_9MHZ 6
-#define PMU0_PLL0_PC0_DIV_ARM_58_6MHZ 7
-
-/* Wildcard base, stop_mod, en_lf_tp, en_cal & lf_r2 */
-#define PMU0_PLL0_PLLCTL1 1
-#define PMU0_PLL0_PC1_WILD_INT_MASK 0xf0000000
-#define PMU0_PLL0_PC1_WILD_INT_SHIFT 28
-#define PMU0_PLL0_PC1_WILD_FRAC_MASK 0x0fffff00
-#define PMU0_PLL0_PC1_WILD_FRAC_SHIFT 8
-#define PMU0_PLL0_PC1_STOP_MOD 0x00000040
-
-/* Wildcard base, vco_calvar, vco_swc, vco_var_selref, vso_ical & vco_sel_avdd */
-#define PMU0_PLL0_PLLCTL2 2
-#define PMU0_PLL0_PC2_WILD_INT_MASK 0xf
-#define PMU0_PLL0_PC2_WILD_INT_SHIFT 4
-
-/* pllcontrol registers */
-/* ndiv_pwrdn, pwrdn_ch<x>, refcomp_pwrdn, dly_ch<x>, p1div, p2div, _bypass_sdmod */
-#define PMU1_PLL0_PLLCTL0 0
-#define PMU1_PLL0_PC0_P1DIV_MASK 0x00f00000
-#define PMU1_PLL0_PC0_P1DIV_SHIFT 20
-#define PMU1_PLL0_PC0_P2DIV_MASK 0x0f000000
-#define PMU1_PLL0_PC0_P2DIV_SHIFT 24
-
-/* m<x>div */
-#define PMU1_PLL0_PLLCTL1 1
-#define PMU1_PLL0_PC1_M1DIV_MASK 0x000000ff
-#define PMU1_PLL0_PC1_M1DIV_SHIFT 0
-#define PMU1_PLL0_PC1_M2DIV_MASK 0x0000ff00
-#define PMU1_PLL0_PC1_M2DIV_SHIFT 8
-#define PMU1_PLL0_PC1_M3DIV_MASK 0x00ff0000
-#define PMU1_PLL0_PC1_M3DIV_SHIFT 16
-#define PMU1_PLL0_PC1_M4DIV_MASK 0xff000000
-#define PMU1_PLL0_PC1_M4DIV_SHIFT 24
-
-#define DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT 8
-#define DOT11MAC_880MHZ_CLK_DIVISOR_MASK (0xFF << DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT)
-#define DOT11MAC_880MHZ_CLK_DIVISOR_VAL (0xE << DOT11MAC_880MHZ_CLK_DIVISOR_SHIFT)
-
-/* m<x>div, ndiv_dither_mfb, ndiv_mode, ndiv_int */
-#define PMU1_PLL0_PLLCTL2 2
-#define PMU1_PLL0_PC2_M5DIV_MASK 0x000000ff
-#define PMU1_PLL0_PC2_M5DIV_SHIFT 0
-#define PMU1_PLL0_PC2_M6DIV_MASK 0x0000ff00
-#define PMU1_PLL0_PC2_M6DIV_SHIFT 8
-#define PMU1_PLL0_PC2_NDIV_MODE_MASK 0x000e0000
-#define PMU1_PLL0_PC2_NDIV_MODE_SHIFT 17
-#define PMU1_PLL0_PC2_NDIV_MODE_MASH 1
-#define PMU1_PLL0_PC2_NDIV_MODE_MFB 2 /* recommended for 4319 */
-#define PMU1_PLL0_PC2_NDIV_INT_MASK 0x1ff00000
-#define PMU1_PLL0_PC2_NDIV_INT_SHIFT 20
-
-/* ndiv_frac */
-#define PMU1_PLL0_PLLCTL3 3
-#define PMU1_PLL0_PC3_NDIV_FRAC_MASK 0x00ffffff
-#define PMU1_PLL0_PC3_NDIV_FRAC_SHIFT 0
-
-/* pll_ctrl */
-#define PMU1_PLL0_PLLCTL4 4
-
-/* pll_ctrl, vco_rng, clkdrive_ch<x> */
-#define PMU1_PLL0_PLLCTL5 5
-#define PMU1_PLL0_PC5_CLK_DRV_MASK 0xffffff00
-#define PMU1_PLL0_PC5_CLK_DRV_SHIFT 8
-
-/* PMU rev 2 control words */
-#define PMU2_PHY_PLL_PLLCTL 4
-#define PMU2_SI_PLL_PLLCTL 10
-
-/* PMU rev 2 */
-/* pllcontrol registers */
-/* ndiv_pwrdn, pwrdn_ch<x>, refcomp_pwrdn, dly_ch<x>, p1div, p2div, _bypass_sdmod */
-#define PMU2_PLL_PLLCTL0 0
-#define PMU2_PLL_PC0_P1DIV_MASK 0x00f00000
-#define PMU2_PLL_PC0_P1DIV_SHIFT 20
-#define PMU2_PLL_PC0_P2DIV_MASK 0x0f000000
-#define PMU2_PLL_PC0_P2DIV_SHIFT 24
-
-/* m<x>div */
-#define PMU2_PLL_PLLCTL1 1
-#define PMU2_PLL_PC1_M1DIV_MASK 0x000000ff
-#define PMU2_PLL_PC1_M1DIV_SHIFT 0
-#define PMU2_PLL_PC1_M2DIV_MASK 0x0000ff00
-#define PMU2_PLL_PC1_M2DIV_SHIFT 8
-#define PMU2_PLL_PC1_M3DIV_MASK 0x00ff0000
-#define PMU2_PLL_PC1_M3DIV_SHIFT 16
-#define PMU2_PLL_PC1_M4DIV_MASK 0xff000000
-#define PMU2_PLL_PC1_M4DIV_SHIFT 24
-
-/* m<x>div, ndiv_dither_mfb, ndiv_mode, ndiv_int */
-#define PMU2_PLL_PLLCTL2 2
-#define PMU2_PLL_PC2_M5DIV_MASK 0x000000ff
-#define PMU2_PLL_PC2_M5DIV_SHIFT 0
-#define PMU2_PLL_PC2_M6DIV_MASK 0x0000ff00
-#define PMU2_PLL_PC2_M6DIV_SHIFT 8
-#define PMU2_PLL_PC2_NDIV_MODE_MASK 0x000e0000
-#define PMU2_PLL_PC2_NDIV_MODE_SHIFT 17
-#define PMU2_PLL_PC2_NDIV_INT_MASK 0x1ff00000
-#define PMU2_PLL_PC2_NDIV_INT_SHIFT 20
-
-/* ndiv_frac */
-#define PMU2_PLL_PLLCTL3 3
-#define PMU2_PLL_PC3_NDIV_FRAC_MASK 0x00ffffff
-#define PMU2_PLL_PC3_NDIV_FRAC_SHIFT 0
-
-/* pll_ctrl */
-#define PMU2_PLL_PLLCTL4 4
-
-/* pll_ctrl, vco_rng, clkdrive_ch<x> */
-#define PMU2_PLL_PLLCTL5 5
-#define PMU2_PLL_PC5_CLKDRIVE_CH1_MASK 0x00000f00
-#define PMU2_PLL_PC5_CLKDRIVE_CH1_SHIFT 8
-#define PMU2_PLL_PC5_CLKDRIVE_CH2_MASK 0x0000f000
-#define PMU2_PLL_PC5_CLKDRIVE_CH2_SHIFT 12
-#define PMU2_PLL_PC5_CLKDRIVE_CH3_MASK 0x000f0000
-#define PMU2_PLL_PC5_CLKDRIVE_CH3_SHIFT 16
-#define PMU2_PLL_PC5_CLKDRIVE_CH4_MASK 0x00f00000
-#define PMU2_PLL_PC5_CLKDRIVE_CH4_SHIFT 20
-#define PMU2_PLL_PC5_CLKDRIVE_CH5_MASK 0x0f000000
-#define PMU2_PLL_PC5_CLKDRIVE_CH5_SHIFT 24
-#define PMU2_PLL_PC5_CLKDRIVE_CH6_MASK 0xf0000000
-#define PMU2_PLL_PC5_CLKDRIVE_CH6_SHIFT 28
-
-/* PMU rev 5 (& 6) */
-#define PMU5_PLL_P1P2_OFF 0
-#define PMU5_PLL_P1_MASK 0x0f000000
-#define PMU5_PLL_P1_SHIFT 24
-#define PMU5_PLL_P2_MASK 0x00f00000
-#define PMU5_PLL_P2_SHIFT 20
-#define PMU5_PLL_M14_OFF 1
-#define PMU5_PLL_MDIV_MASK 0x000000ff
-#define PMU5_PLL_MDIV_WIDTH 8
-#define PMU5_PLL_NM5_OFF 2
-#define PMU5_PLL_NDIV_MASK 0xfff00000
-#define PMU5_PLL_NDIV_SHIFT 20
-#define PMU5_PLL_NDIV_MODE_MASK 0x000e0000
-#define PMU5_PLL_NDIV_MODE_SHIFT 17
-#define PMU5_PLL_FMAB_OFF 3
-#define PMU5_PLL_MRAT_MASK 0xf0000000
-#define PMU5_PLL_MRAT_SHIFT 28
-#define PMU5_PLL_ABRAT_MASK 0x08000000
-#define PMU5_PLL_ABRAT_SHIFT 27
-#define PMU5_PLL_FDIV_MASK 0x07ffffff
-#define PMU5_PLL_PLLCTL_OFF 4
-#define PMU5_PLL_PCHI_OFF 5
-#define PMU5_PLL_PCHI_MASK 0x0000003f
-
-/* pmu XtalFreqRatio */
-#define PMU_XTALFREQ_REG_ILPCTR_MASK 0x00001FFF
-#define PMU_XTALFREQ_REG_MEASURE_MASK 0x80000000
-#define PMU_XTALFREQ_REG_MEASURE_SHIFT 31
-
-/* Divider allocation in 4716/47162/5356/5357 */
-#define PMU5_MAINPLL_CPU 1
-#define PMU5_MAINPLL_MEM 2
-#define PMU5_MAINPLL_SI 3
-
-#define PMU7_PLL_PLLCTL7 7
-#define PMU7_PLL_PLLCTL8 8
-#define PMU7_PLL_PLLCTL11 11
-
-/* PLL usage in 4716/47162 */
-#define PMU4716_MAINPLL_PLL0 12
-
-/* PLL usage in 5356/5357 */
-#define PMU5356_MAINPLL_PLL0 0
-#define PMU5357_MAINPLL_PLL0 0
-
-/* 4716/47162 resources */
-#define RES4716_PROC_PLL_ON 0x00000040
-#define RES4716_PROC_HT_AVAIL 0x00000080
-
-/* 4716/4717/4718 Chip specific ChipControl register bits */
-#define CCTRL471X_I2S_PINS_ENABLE 0x0080 /* I2S pins off by default, shared with pflash */
-
-/* 5354 resources */
-#define RES5354_EXT_SWITCHER_PWM 0 /* 0x00001 */
-#define RES5354_BB_SWITCHER_PWM 1 /* 0x00002 */
-#define RES5354_BB_SWITCHER_BURST 2 /* 0x00004 */
-#define RES5354_BB_EXT_SWITCHER_BURST 3 /* 0x00008 */
-#define RES5354_ILP_REQUEST 4 /* 0x00010 */
-#define RES5354_RADIO_SWITCHER_PWM 5 /* 0x00020 */
-#define RES5354_RADIO_SWITCHER_BURST 6 /* 0x00040 */
-#define RES5354_ROM_SWITCH 7 /* 0x00080 */
-#define RES5354_PA_REF_LDO 8 /* 0x00100 */
-#define RES5354_RADIO_LDO 9 /* 0x00200 */
-#define RES5354_AFE_LDO 10 /* 0x00400 */
-#define RES5354_PLL_LDO 11 /* 0x00800 */
-#define RES5354_BG_FILTBYP 12 /* 0x01000 */
-#define RES5354_TX_FILTBYP 13 /* 0x02000 */
-#define RES5354_RX_FILTBYP 14 /* 0x04000 */
-#define RES5354_XTAL_PU 15 /* 0x08000 */
-#define RES5354_XTAL_EN 16 /* 0x10000 */
-#define RES5354_BB_PLL_FILTBYP 17 /* 0x20000 */
-#define RES5354_RF_PLL_FILTBYP 18 /* 0x40000 */
-#define RES5354_BB_PLL_PU 19 /* 0x80000 */
-
-/* 5357 Chip specific ChipControl register bits */
-#define CCTRL5357_EXTPA (1<<14) /* extPA in ChipControl 1, bit 14 */
-#define CCTRL5357_ANT_MUX_2o3 (1<<15) /* 2o3 in ChipControl 1, bit 15 */
-
-/* 4328 resources */
-#define RES4328_EXT_SWITCHER_PWM 0 /* 0x00001 */
-#define RES4328_BB_SWITCHER_PWM 1 /* 0x00002 */
-#define RES4328_BB_SWITCHER_BURST 2 /* 0x00004 */
-#define RES4328_BB_EXT_SWITCHER_BURST 3 /* 0x00008 */
-#define RES4328_ILP_REQUEST 4 /* 0x00010 */
-#define RES4328_RADIO_SWITCHER_PWM 5 /* 0x00020 */
-#define RES4328_RADIO_SWITCHER_BURST 6 /* 0x00040 */
-#define RES4328_ROM_SWITCH 7 /* 0x00080 */
-#define RES4328_PA_REF_LDO 8 /* 0x00100 */
-#define RES4328_RADIO_LDO 9 /* 0x00200 */
-#define RES4328_AFE_LDO 10 /* 0x00400 */
-#define RES4328_PLL_LDO 11 /* 0x00800 */
-#define RES4328_BG_FILTBYP 12 /* 0x01000 */
-#define RES4328_TX_FILTBYP 13 /* 0x02000 */
-#define RES4328_RX_FILTBYP 14 /* 0x04000 */
-#define RES4328_XTAL_PU 15 /* 0x08000 */
-#define RES4328_XTAL_EN 16 /* 0x10000 */
-#define RES4328_BB_PLL_FILTBYP 17 /* 0x20000 */
-#define RES4328_RF_PLL_FILTBYP 18 /* 0x40000 */
-#define RES4328_BB_PLL_PU 19 /* 0x80000 */
-
-/* 4325 A0/A1 resources */
-#define RES4325_BUCK_BOOST_BURST 0 /* 0x00000001 */
-#define RES4325_CBUCK_BURST 1 /* 0x00000002 */
-#define RES4325_CBUCK_PWM 2 /* 0x00000004 */
-#define RES4325_CLDO_CBUCK_BURST 3 /* 0x00000008 */
-#define RES4325_CLDO_CBUCK_PWM 4 /* 0x00000010 */
-#define RES4325_BUCK_BOOST_PWM 5 /* 0x00000020 */
-#define RES4325_ILP_REQUEST 6 /* 0x00000040 */
-#define RES4325_ABUCK_BURST 7 /* 0x00000080 */
-#define RES4325_ABUCK_PWM 8 /* 0x00000100 */
-#define RES4325_LNLDO1_PU 9 /* 0x00000200 */
-#define RES4325_OTP_PU 10 /* 0x00000400 */
-#define RES4325_LNLDO3_PU 11 /* 0x00000800 */
-#define RES4325_LNLDO4_PU 12 /* 0x00001000 */
-#define RES4325_XTAL_PU 13 /* 0x00002000 */
-#define RES4325_ALP_AVAIL 14 /* 0x00004000 */
-#define RES4325_RX_PWRSW_PU 15 /* 0x00008000 */
-#define RES4325_TX_PWRSW_PU 16 /* 0x00010000 */
-#define RES4325_RFPLL_PWRSW_PU 17 /* 0x00020000 */
-#define RES4325_LOGEN_PWRSW_PU 18 /* 0x00040000 */
-#define RES4325_AFE_PWRSW_PU 19 /* 0x00080000 */
-#define RES4325_BBPLL_PWRSW_PU 20 /* 0x00100000 */
-#define RES4325_HT_AVAIL 21 /* 0x00200000 */
-
-/* 4325 B0/C0 resources */
-#define RES4325B0_CBUCK_LPOM 1 /* 0x00000002 */
-#define RES4325B0_CBUCK_BURST 2 /* 0x00000004 */
-#define RES4325B0_CBUCK_PWM 3 /* 0x00000008 */
-#define RES4325B0_CLDO_PU 4 /* 0x00000010 */
-
-/* 4325 C1 resources */
-#define RES4325C1_LNLDO2_PU 12 /* 0x00001000 */
-
-/* 4325 chip-specific ChipStatus register bits */
-#define CST4325_SPROM_OTP_SEL_MASK 0x00000003
-#define CST4325_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */
-#define CST4325_SPROM_SEL 1 /* OTP is powered up, SPROM is present */
-#define CST4325_OTP_SEL 2 /* OTP is powered up, no SPROM */
-#define CST4325_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */
-#define CST4325_SDIO_USB_MODE_MASK 0x00000004
-#define CST4325_SDIO_USB_MODE_SHIFT 2
-#define CST4325_RCAL_VALID_MASK 0x00000008
-#define CST4325_RCAL_VALID_SHIFT 3
-#define CST4325_RCAL_VALUE_MASK 0x000001f0
-#define CST4325_RCAL_VALUE_SHIFT 4
-#define CST4325_PMUTOP_2B_MASK 0x00000200 /* 1 for 2b, 0 for to 2a */
-#define CST4325_PMUTOP_2B_SHIFT 9
-
-#define RES4329_RESERVED0 0 /* 0x00000001 */
-#define RES4329_CBUCK_LPOM 1 /* 0x00000002 */
-#define RES4329_CBUCK_BURST 2 /* 0x00000004 */
-#define RES4329_CBUCK_PWM 3 /* 0x00000008 */
-#define RES4329_CLDO_PU 4 /* 0x00000010 */
-#define RES4329_PALDO_PU 5 /* 0x00000020 */
-#define RES4329_ILP_REQUEST 6 /* 0x00000040 */
-#define RES4329_RESERVED7 7 /* 0x00000080 */
-#define RES4329_RESERVED8 8 /* 0x00000100 */
-#define RES4329_LNLDO1_PU 9 /* 0x00000200 */
-#define RES4329_OTP_PU 10 /* 0x00000400 */
-#define RES4329_RESERVED11 11 /* 0x00000800 */
-#define RES4329_LNLDO2_PU 12 /* 0x00001000 */
-#define RES4329_XTAL_PU 13 /* 0x00002000 */
-#define RES4329_ALP_AVAIL 14 /* 0x00004000 */
-#define RES4329_RX_PWRSW_PU 15 /* 0x00008000 */
-#define RES4329_TX_PWRSW_PU 16 /* 0x00010000 */
-#define RES4329_RFPLL_PWRSW_PU 17 /* 0x00020000 */
-#define RES4329_LOGEN_PWRSW_PU 18 /* 0x00040000 */
-#define RES4329_AFE_PWRSW_PU 19 /* 0x00080000 */
-#define RES4329_BBPLL_PWRSW_PU 20 /* 0x00100000 */
-#define RES4329_HT_AVAIL 21 /* 0x00200000 */
-
-#define CST4329_SPROM_OTP_SEL_MASK 0x00000003
-#define CST4329_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */
-#define CST4329_SPROM_SEL 1 /* OTP is powered up, SPROM is present */
-#define CST4329_OTP_SEL 2 /* OTP is powered up, no SPROM */
-#define CST4329_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */
-#define CST4329_SPI_SDIO_MODE_MASK 0x00000004
-#define CST4329_SPI_SDIO_MODE_SHIFT 2
-
-/* 4312 chip-specific ChipStatus register bits */
-#define CST4312_SPROM_OTP_SEL_MASK 0x00000003
-#define CST4312_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */
-#define CST4312_SPROM_SEL 1 /* OTP is powered up, SPROM is present */
-#define CST4312_OTP_SEL 2 /* OTP is powered up, no SPROM */
-#define CST4312_OTP_BAD 3 /* OTP is broken, SPROM is present */
-
-/* 4312 resources (all PMU chips with little memory constraint) */
-#define RES4312_SWITCHER_BURST 0 /* 0x00000001 */
-#define RES4312_SWITCHER_PWM 1 /* 0x00000002 */
-#define RES4312_PA_REF_LDO 2 /* 0x00000004 */
-#define RES4312_CORE_LDO_BURST 3 /* 0x00000008 */
-#define RES4312_CORE_LDO_PWM 4 /* 0x00000010 */
-#define RES4312_RADIO_LDO 5 /* 0x00000020 */
-#define RES4312_ILP_REQUEST 6 /* 0x00000040 */
-#define RES4312_BG_FILTBYP 7 /* 0x00000080 */
-#define RES4312_TX_FILTBYP 8 /* 0x00000100 */
-#define RES4312_RX_FILTBYP 9 /* 0x00000200 */
-#define RES4312_XTAL_PU 10 /* 0x00000400 */
-#define RES4312_ALP_AVAIL 11 /* 0x00000800 */
-#define RES4312_BB_PLL_FILTBYP 12 /* 0x00001000 */
-#define RES4312_RF_PLL_FILTBYP 13 /* 0x00002000 */
-#define RES4312_HT_AVAIL 14 /* 0x00004000 */
-
-/* 4322 resources */
-#define RES4322_RF_LDO 0
-#define RES4322_ILP_REQUEST 1
-#define RES4322_XTAL_PU 2
-#define RES4322_ALP_AVAIL 3
-#define RES4322_SI_PLL_ON 4
-#define RES4322_HT_SI_AVAIL 5
-#define RES4322_PHY_PLL_ON 6
-#define RES4322_HT_PHY_AVAIL 7
-#define RES4322_OTP_PU 8
-
-/* 4322 chip-specific ChipStatus register bits */
-#define CST4322_XTAL_FREQ_20_40MHZ 0x00000020
-#define CST4322_SPROM_OTP_SEL_MASK 0x000000c0
-#define CST4322_SPROM_OTP_SEL_SHIFT 6
-#define CST4322_NO_SPROM_OTP 0 /* no OTP, no SPROM */
-#define CST4322_SPROM_PRESENT 1 /* SPROM is present */
-#define CST4322_OTP_PRESENT 2 /* OTP is present */
-#define CST4322_PCI_OR_USB 0x00000100
-#define CST4322_BOOT_MASK 0x00000600
-#define CST4322_BOOT_SHIFT 9
-#define CST4322_BOOT_FROM_SRAM 0 /* boot from SRAM, ARM in reset */
-#define CST4322_BOOT_FROM_ROM 1 /* boot from ROM */
-#define CST4322_BOOT_FROM_FLASH 2 /* boot from FLASH */
-#define CST4322_BOOT_FROM_INVALID 3
-#define CST4322_ILP_DIV_EN 0x00000800
-#define CST4322_FLASH_TYPE_MASK 0x00001000
-#define CST4322_FLASH_TYPE_SHIFT 12
-#define CST4322_FLASH_TYPE_SHIFT_ST 0 /* ST serial FLASH */
-#define CST4322_FLASH_TYPE_SHIFT_ATMEL 1 /* ATMEL flash */
-#define CST4322_ARM_TAP_SEL 0x00002000
-#define CST4322_RES_INIT_MODE_MASK 0x0000c000
-#define CST4322_RES_INIT_MODE_SHIFT 14
-#define CST4322_RES_INIT_MODE_ILPAVAIL 0 /* resinitmode: ILP available */
-#define CST4322_RES_INIT_MODE_ILPREQ 1 /* resinitmode: ILP request */
-#define CST4322_RES_INIT_MODE_ALPAVAIL 2 /* resinitmode: ALP available */
-#define CST4322_RES_INIT_MODE_HTAVAIL 3 /* resinitmode: HT available */
-#define CST4322_PCIPLLCLK_GATING 0x00010000
-#define CST4322_CLK_SWITCH_PCI_TO_ALP 0x00020000
-#define CST4322_PCI_CARDBUS_MODE 0x00040000
-
-/* 43224 chip-specific ChipControl register bits */
-#define CCTRL43224_GPIO_TOGGLE 0x8000
-#define CCTRL_43224A0_12MA_LED_DRIVE 0x00F000F0 /* 12 mA drive strength */
-#define CCTRL_43224B0_12MA_LED_DRIVE 0xF0 /* 12 mA drive strength for later 43224s */
-
-/* 43236 resources */
-#define RES43236_REGULATOR 0
-#define RES43236_ILP_REQUEST 1
-#define RES43236_XTAL_PU 2
-#define RES43236_ALP_AVAIL 3
-#define RES43236_SI_PLL_ON 4
-#define RES43236_HT_SI_AVAIL 5
-
-/* 43236 chip-specific ChipControl register bits */
-#define CCTRL43236_BT_COEXIST (1<<0) /* 0 disable */
-#define CCTRL43236_SECI (1<<1) /* 0 SECI is disabled (JATG functional) */
-#define CCTRL43236_EXT_LNA (1<<2) /* 0 disable */
-#define CCTRL43236_ANT_MUX_2o3 (1<<3) /* 2o3 mux, chipcontrol bit 3 */
-#define CCTRL43236_GSIO (1<<4) /* 0 disable */
-
-/* 43236 Chip specific ChipStatus register bits */
-#define CST43236_SFLASH_MASK 0x00000040
-#define CST43236_OTP_MASK 0x00000080
-#define CST43236_HSIC_MASK 0x00000100 /* USB/HSIC */
-#define CST43236_BP_CLK 0x00000200 /* 120/96Mbps */
-#define CST43236_BOOT_MASK 0x00001800
-#define CST43236_BOOT_SHIFT 11
-#define CST43236_BOOT_FROM_SRAM 0 /* boot from SRAM, ARM in reset */
-#define CST43236_BOOT_FROM_ROM 1 /* boot from ROM */
-#define CST43236_BOOT_FROM_FLASH 2 /* boot from FLASH */
-#define CST43236_BOOT_FROM_INVALID 3
-
-/* 4331 resources */
-#define RES4331_REGULATOR 0
-#define RES4331_ILP_REQUEST 1
-#define RES4331_XTAL_PU 2
-#define RES4331_ALP_AVAIL 3
-#define RES4331_SI_PLL_ON 4
-#define RES4331_HT_SI_AVAIL 5
-
-/* 4331 chip-specific ChipControl register bits */
-#define CCTRL4331_BT_COEXIST (1<<0) /* 0 disable */
-#define CCTRL4331_SECI (1<<1) /* 0 SECI is disabled (JATG functional) */
-#define CCTRL4331_EXT_LNA (1<<2) /* 0 disable */
-#define CCTRL4331_SPROM_GPIO13_15 (1<<3) /* sprom/gpio13-15 mux */
-#define CCTRL4331_EXTPA_EN (1<<4) /* 0 ext pa disable, 1 ext pa enabled */
-#define CCTRL4331_GPIOCLK_ON_SPROMCS (1<<5) /* set drive out GPIO_CLK on sprom_cs pin */
-#define CCTRL4331_PCIE_MDIO_ON_SPROMCS (1<<6) /* use sprom_cs pin as PCIE mdio interface */
-#define CCTRL4331_EXTPA_ON_GPIO2_5 (1<<7) /* aband extpa will be at gpio2/5 and sprom_dout */
-#define CCTRL4331_OVR_PIPEAUXCLKEN (1<<8) /* override core control on pipe_AuxClkEnable */
-#define CCTRL4331_OVR_PIPEAUXPWRDOWN (1<<9) /* override core control on pipe_AuxPowerDown */
-#define CCTRL4331_PCIE_AUXCLKEN (1<<10) /* pcie_auxclkenable */
-#define CCTRL4331_PCIE_PIPE_PLLDOWN (1<<11) /* pcie_pipe_pllpowerdown */
-#define CCTRL4331_BT_SHD0_ON_GPIO4 (1<<16) /* enable bt_shd0 at gpio4 */
-#define CCTRL4331_BT_SHD1_ON_GPIO5 (1<<17) /* enable bt_shd1 at gpio5 */
-
-/* 4331 Chip specific ChipStatus register bits */
-#define CST4331_XTAL_FREQ 0x00000001 /* crystal frequency 20/40Mhz */
-#define CST4331_SPROM_PRESENT 0x00000002
-#define CST4331_OTP_PRESENT 0x00000004
-#define CST4331_LDO_RF 0x00000008
-#define CST4331_LDO_PAR 0x00000010
-
-/* 4315 resources */
-#define RES4315_CBUCK_LPOM 1 /* 0x00000002 */
-#define RES4315_CBUCK_BURST 2 /* 0x00000004 */
-#define RES4315_CBUCK_PWM 3 /* 0x00000008 */
-#define RES4315_CLDO_PU 4 /* 0x00000010 */
-#define RES4315_PALDO_PU 5 /* 0x00000020 */
-#define RES4315_ILP_REQUEST 6 /* 0x00000040 */
-#define RES4315_LNLDO1_PU 9 /* 0x00000200 */
-#define RES4315_OTP_PU 10 /* 0x00000400 */
-#define RES4315_LNLDO2_PU 12 /* 0x00001000 */
-#define RES4315_XTAL_PU 13 /* 0x00002000 */
-#define RES4315_ALP_AVAIL 14 /* 0x00004000 */
-#define RES4315_RX_PWRSW_PU 15 /* 0x00008000 */
-#define RES4315_TX_PWRSW_PU 16 /* 0x00010000 */
-#define RES4315_RFPLL_PWRSW_PU 17 /* 0x00020000 */
-#define RES4315_LOGEN_PWRSW_PU 18 /* 0x00040000 */
-#define RES4315_AFE_PWRSW_PU 19 /* 0x00080000 */
-#define RES4315_BBPLL_PWRSW_PU 20 /* 0x00100000 */
-#define RES4315_HT_AVAIL 21 /* 0x00200000 */
-
-/* 4315 chip-specific ChipStatus register bits */
-#define CST4315_SPROM_OTP_SEL_MASK 0x00000003 /* gpio [7:6], SDIO CIS selection */
-#define CST4315_DEFCIS_SEL 0x00000000 /* use default CIS, OTP is powered up */
-#define CST4315_SPROM_SEL 0x00000001 /* use SPROM, OTP is powered up */
-#define CST4315_OTP_SEL 0x00000002 /* use OTP, OTP is powered up */
-#define CST4315_OTP_PWRDN 0x00000003 /* use SPROM, OTP is powered down */
-#define CST4315_SDIO_MODE 0x00000004 /* gpio [8], sdio/usb mode */
-#define CST4315_RCAL_VALID 0x00000008
-#define CST4315_RCAL_VALUE_MASK 0x000001f0
-#define CST4315_RCAL_VALUE_SHIFT 4
-#define CST4315_PALDO_EXTPNP 0x00000200 /* PALDO is configured with external PNP */
-#define CST4315_CBUCK_MODE_MASK 0x00000c00
-#define CST4315_CBUCK_MODE_BURST 0x00000400
-#define CST4315_CBUCK_MODE_LPBURST 0x00000c00
-
-/* 4319 resources */
-#define RES4319_CBUCK_LPOM 1 /* 0x00000002 */
-#define RES4319_CBUCK_BURST 2 /* 0x00000004 */
-#define RES4319_CBUCK_PWM 3 /* 0x00000008 */
-#define RES4319_CLDO_PU 4 /* 0x00000010 */
-#define RES4319_PALDO_PU 5 /* 0x00000020 */
-#define RES4319_ILP_REQUEST 6 /* 0x00000040 */
-#define RES4319_LNLDO1_PU 9 /* 0x00000200 */
-#define RES4319_OTP_PU 10 /* 0x00000400 */
-#define RES4319_LNLDO2_PU 12 /* 0x00001000 */
-#define RES4319_XTAL_PU 13 /* 0x00002000 */
-#define RES4319_ALP_AVAIL 14 /* 0x00004000 */
-#define RES4319_RX_PWRSW_PU 15 /* 0x00008000 */
-#define RES4319_TX_PWRSW_PU 16 /* 0x00010000 */
-#define RES4319_RFPLL_PWRSW_PU 17 /* 0x00020000 */
-#define RES4319_LOGEN_PWRSW_PU 18 /* 0x00040000 */
-#define RES4319_AFE_PWRSW_PU 19 /* 0x00080000 */
-#define RES4319_BBPLL_PWRSW_PU 20 /* 0x00100000 */
-#define RES4319_HT_AVAIL 21 /* 0x00200000 */
-
-/* 4319 chip-specific ChipStatus register bits */
-#define CST4319_SPI_CPULESSUSB 0x00000001
-#define CST4319_SPI_CLK_POL 0x00000002
-#define CST4319_SPI_CLK_PH 0x00000008
-#define CST4319_SPROM_OTP_SEL_MASK 0x000000c0 /* gpio [7:6], SDIO CIS selection */
-#define CST4319_SPROM_OTP_SEL_SHIFT 6
-#define CST4319_DEFCIS_SEL 0x00000000 /* use default CIS, OTP is powered up */
-#define CST4319_SPROM_SEL 0x00000040 /* use SPROM, OTP is powered up */
-#define CST4319_OTP_SEL 0x00000080 /* use OTP, OTP is powered up */
-#define CST4319_OTP_PWRDN 0x000000c0 /* use SPROM, OTP is powered down */
-#define CST4319_SDIO_USB_MODE 0x00000100 /* gpio [8], sdio/usb mode */
-#define CST4319_REMAP_SEL_MASK 0x00000600
-#define CST4319_ILPDIV_EN 0x00000800
-#define CST4319_XTAL_PD_POL 0x00001000
-#define CST4319_LPO_SEL 0x00002000
-#define CST4319_RES_INIT_MODE 0x0000c000
-#define CST4319_PALDO_EXTPNP 0x00010000 /* PALDO is configured with external PNP */
-#define CST4319_CBUCK_MODE_MASK 0x00060000
-#define CST4319_CBUCK_MODE_BURST 0x00020000
-#define CST4319_CBUCK_MODE_LPBURST 0x00060000
-#define CST4319_RCAL_VALID 0x01000000
-#define CST4319_RCAL_VALUE_MASK 0x3e000000
-#define CST4319_RCAL_VALUE_SHIFT 25
-
-#define PMU1_PLL0_CHIPCTL0 0
-#define PMU1_PLL0_CHIPCTL1 1
-#define PMU1_PLL0_CHIPCTL2 2
-#define CCTL_4319USB_XTAL_SEL_MASK 0x00180000
-#define CCTL_4319USB_XTAL_SEL_SHIFT 19
-#define CCTL_4319USB_48MHZ_PLL_SEL 1
-#define CCTL_4319USB_24MHZ_PLL_SEL 2
-
-/* PMU resources for 4336 */
-#define RES4336_CBUCK_LPOM 0
-#define RES4336_CBUCK_BURST 1
-#define RES4336_CBUCK_LP_PWM 2
-#define RES4336_CBUCK_PWM 3
-#define RES4336_CLDO_PU 4
-#define RES4336_DIS_INT_RESET_PD 5
-#define RES4336_ILP_REQUEST 6
-#define RES4336_LNLDO_PU 7
-#define RES4336_LDO3P3_PU 8
-#define RES4336_OTP_PU 9
-#define RES4336_XTAL_PU 10
-#define RES4336_ALP_AVAIL 11
-#define RES4336_RADIO_PU 12
-#define RES4336_BG_PU 13
-#define RES4336_VREG1p4_PU_PU 14
-#define RES4336_AFE_PWRSW_PU 15
-#define RES4336_RX_PWRSW_PU 16
-#define RES4336_TX_PWRSW_PU 17
-#define RES4336_BB_PWRSW_PU 18
-#define RES4336_SYNTH_PWRSW_PU 19
-#define RES4336_MISC_PWRSW_PU 20
-#define RES4336_LOGEN_PWRSW_PU 21
-#define RES4336_BBPLL_PWRSW_PU 22
-#define RES4336_MACPHY_CLKAVAIL 23
-#define RES4336_HT_AVAIL 24
-#define RES4336_RSVD 25
-
-/* 4336 chip-specific ChipStatus register bits */
-#define CST4336_SPI_MODE_MASK 0x00000001
-#define CST4336_SPROM_PRESENT 0x00000002
-#define CST4336_OTP_PRESENT 0x00000004
-#define CST4336_ARMREMAP_0 0x00000008
-#define CST4336_ILPDIV_EN_MASK 0x00000010
-#define CST4336_ILPDIV_EN_SHIFT 4
-#define CST4336_XTAL_PD_POL_MASK 0x00000020
-#define CST4336_XTAL_PD_POL_SHIFT 5
-#define CST4336_LPO_SEL_MASK 0x00000040
-#define CST4336_LPO_SEL_SHIFT 6
-#define CST4336_RES_INIT_MODE_MASK 0x00000180
-#define CST4336_RES_INIT_MODE_SHIFT 7
-#define CST4336_CBUCK_MODE_MASK 0x00000600
-#define CST4336_CBUCK_MODE_SHIFT 9
-
-/* 4330 resources */
-#define RES4330_CBUCK_LPOM 0
-#define RES4330_CBUCK_BURST 1
-#define RES4330_CBUCK_LP_PWM 2
-#define RES4330_CBUCK_PWM 3
-#define RES4330_CLDO_PU 4
-#define RES4330_DIS_INT_RESET_PD 5
-#define RES4330_ILP_REQUEST 6
-#define RES4330_LNLDO_PU 7
-#define RES4330_LDO3P3_PU 8
-#define RES4330_OTP_PU 9
-#define RES4330_XTAL_PU 10
-#define RES4330_ALP_AVAIL 11
-#define RES4330_RADIO_PU 12
-#define RES4330_BG_PU 13
-#define RES4330_VREG1p4_PU_PU 14
-#define RES4330_AFE_PWRSW_PU 15
-#define RES4330_RX_PWRSW_PU 16
-#define RES4330_TX_PWRSW_PU 17
-#define RES4330_BB_PWRSW_PU 18
-#define RES4330_SYNTH_PWRSW_PU 19
-#define RES4330_MISC_PWRSW_PU 20
-#define RES4330_LOGEN_PWRSW_PU 21
-#define RES4330_BBPLL_PWRSW_PU 22
-#define RES4330_MACPHY_CLKAVAIL 23
-#define RES4330_HT_AVAIL 24
-#define RES4330_5gRX_PWRSW_PU 25
-#define RES4330_5gTX_PWRSW_PU 26
-#define RES4330_5g_LOGEN_PWRSW_PU 27
-
-/* 4330 chip-specific ChipStatus register bits */
-#define CST4330_CHIPMODE_SDIOD(cs) (((cs) & 0x7) < 6) /* SDIO || gSPI */
-#define CST4330_CHIPMODE_USB20D(cs) (((cs) & 0x7) >= 6) /* USB || USBDA */
-#define CST4330_CHIPMODE_SDIO(cs) (((cs) & 0x4) == 0) /* SDIO */
-#define CST4330_CHIPMODE_GSPI(cs) (((cs) & 0x6) == 4) /* gSPI */
-#define CST4330_CHIPMODE_USB(cs) (((cs) & 0x7) == 6) /* USB packet-oriented */
-#define CST4330_CHIPMODE_USBDA(cs) (((cs) & 0x7) == 7) /* USB Direct Access */
-#define CST4330_OTP_PRESENT 0x00000010
-#define CST4330_LPO_AUTODET_EN 0x00000020
-#define CST4330_ARMREMAP_0 0x00000040
-#define CST4330_SPROM_PRESENT 0x00000080 /* takes priority over OTP if both set */
-#define CST4330_ILPDIV_EN 0x00000100
-#define CST4330_LPO_SEL 0x00000200
-#define CST4330_RES_INIT_MODE_SHIFT 10
-#define CST4330_RES_INIT_MODE_MASK 0x00000c00
-#define CST4330_CBUCK_MODE_SHIFT 12
-#define CST4330_CBUCK_MODE_MASK 0x00003000
-#define CST4330_CBUCK_POWER_OK 0x00004000
-#define CST4330_BB_PLL_LOCKED 0x00008000
-#define SOCDEVRAM_4330_BP_ADDR 0x1E000000
-#define SOCDEVRAM_4330_ARM_ADDR 0x00800000
-
-/* 4313 resources */
-#define RES4313_BB_PU_RSRC 0
-#define RES4313_ILP_REQ_RSRC 1
-#define RES4313_XTAL_PU_RSRC 2
-#define RES4313_ALP_AVAIL_RSRC 3
-#define RES4313_RADIO_PU_RSRC 4
-#define RES4313_BG_PU_RSRC 5
-#define RES4313_VREG1P4_PU_RSRC 6
-#define RES4313_AFE_PWRSW_RSRC 7
-#define RES4313_RX_PWRSW_RSRC 8
-#define RES4313_TX_PWRSW_RSRC 9
-#define RES4313_BB_PWRSW_RSRC 10
-#define RES4313_SYNTH_PWRSW_RSRC 11
-#define RES4313_MISC_PWRSW_RSRC 12
-#define RES4313_BB_PLL_PWRSW_RSRC 13
-#define RES4313_HT_AVAIL_RSRC 14
-#define RES4313_MACPHY_CLK_AVAIL_RSRC 15
-
-/* 4313 chip-specific ChipStatus register bits */
-#define CST4313_SPROM_PRESENT 1
-#define CST4313_OTP_PRESENT 2
-#define CST4313_SPROM_OTP_SEL_MASK 0x00000002
-#define CST4313_SPROM_OTP_SEL_SHIFT 0
-
-/* 4313 Chip specific ChipControl register bits */
-#define CCTRL_4313_12MA_LED_DRIVE 0x00000007 /* 12 mA drive strengh for later 4313 */
-
-/* 43228 resources */
-#define RES43228_NOT_USED 0
-#define RES43228_ILP_REQUEST 1
-#define RES43228_XTAL_PU 2
-#define RES43228_ALP_AVAIL 3
-#define RES43228_PLL_EN 4
-#define RES43228_HT_PHY_AVAIL 5
-
-/* 43228 chipstatus reg bits */
-#define CST43228_ILP_DIV_EN 0x1
-#define CST43228_OTP_PRESENT 0x2
-#define CST43228_SERDES_REFCLK_PADSEL 0x4
-#define CST43228_SDIO_MODE 0x8
-
-#define CST43228_SDIO_OTP_PRESENT 0x10
-#define CST43228_SDIO_RESET 0x20
-
/*
* Maximum delay for the PMU state transition in us.
* This is an upper bound intended for spinwaits etc.
*/
#define PMU_MAX_TRANSITION_DLY 15000
-/* PMU resource up transition time in ILP cycles */
-#define PMURES_UP_TRANSITION 2
-
-/*
-* Register eci_inputlo bitfield values.
-* - BT packet type information bits [7:0]
-*/
-/* [3:0] - Task (link) type */
-#define BT_ACL 0x00
-#define BT_SCO 0x01
-#define BT_eSCO 0x02
-#define BT_A2DP 0x03
-#define BT_SNIFF 0x04
-#define BT_PAGE_SCAN 0x05
-#define BT_INQUIRY_SCAN 0x06
-#define BT_PAGE 0x07
-#define BT_INQUIRY 0x08
-#define BT_MSS 0x09
-#define BT_PARK 0x0a
-#define BT_RSSISCAN 0x0b
-#define BT_MD_ACL 0x0c
-#define BT_MD_eSCO 0x0d
-#define BT_SCAN_WITH_SCO_LINK 0x0e
-#define BT_SCAN_WITHOUT_SCO_LINK 0x0f
-/* [7:4] = packet duration code */
-/* [8] - Master / Slave */
-#define BT_MASTER 0
-#define BT_SLAVE 1
-/* [11:9] - multi-level priority */
-#define BT_LOWEST_PRIO 0x0
-#define BT_HIGHEST_PRIO 0x3
-
-/* WLAN - number of antenna */
-#define WLAN_NUM_ANT1 TXANT_0
-#define WLAN_NUM_ANT2 TXANT_1
-
#endif /* _SBCHIPC_H */
#define PAD _XSTR(__LINE__)
#endif
-/* enumeration in SB is based on the premise that cores are contiguos in the
- * enumeration space.
- */
-#define SB_BUS_SIZE 0x10000 /* Each bus gets 64Kbytes for cores */
-#define SB_BUS_BASE(b) (SI_ENUM_BASE + (b) * SB_BUS_SIZE)
-#define SB_BUS_MAXCORES (SB_BUS_SIZE / SI_CORE_SIZE) /* Max cores per bus */
-
/*
* Sonics Configuration Space Registers.
*/
#define SBCONFIGOFF 0xf00 /* core sbconfig regs are top 256bytes of regs */
-#define SBCONFIGSIZE 256 /* sizeof (sbconfig_t) */
-
-#define SBIPSFLAG 0x08
-#define SBTPSFLAG 0x18
-#define SBTMERRLOGA 0x48 /* sonics >= 2.3 */
-#define SBTMERRLOG 0x50 /* sonics >= 2.3 */
-#define SBADMATCH3 0x60
-#define SBADMATCH2 0x68
-#define SBADMATCH1 0x70
-#define SBIMSTATE 0x90
-#define SBINTVEC 0x94
-#define SBTMSTATELOW 0x98
-#define SBTMSTATEHIGH 0x9c
-#define SBBWA0 0xa0
-#define SBIMCONFIGLOW 0xa8
-#define SBIMCONFIGHIGH 0xac
-#define SBADMATCH0 0xb0
-#define SBTMCONFIGLOW 0xb8
-#define SBTMCONFIGHIGH 0xbc
-#define SBBCONFIG 0xc0
-#define SBBSTATE 0xc8
-#define SBACTCNFG 0xd8
-#define SBFLAGST 0xe8
-#define SBIDLOW 0xf8
-#define SBIDHIGH 0xfc
-
-/* All the previous registers are above SBCONFIGOFF, but with Sonics 2.3, we have
- * a few registers *below* that line. I think it would be very confusing to try
- * and change the value of SBCONFIGOFF, so I'm definig them as absolute offsets here,
- */
-
-#define SBIMERRLOGA 0xea8
-#define SBIMERRLOG 0xeb0
-#define SBTMPORTCONNID0 0xed8
-#define SBTMPORTLOCK0 0xef8
-
-#ifndef _LANGUAGE_ASSEMBLY
-
-typedef volatile struct _sbconfig {
- u32 PAD[2];
- u32 sbipsflag; /* initiator port ocp slave flag */
- u32 PAD[3];
- u32 sbtpsflag; /* target port ocp slave flag */
- u32 PAD[11];
- u32 sbtmerrloga; /* (sonics >= 2.3) */
- u32 PAD;
- u32 sbtmerrlog; /* (sonics >= 2.3) */
- u32 PAD[3];
- u32 sbadmatch3; /* address match3 */
- u32 PAD;
- u32 sbadmatch2; /* address match2 */
- u32 PAD;
- u32 sbadmatch1; /* address match1 */
- u32 PAD[7];
- u32 sbimstate; /* initiator agent state */
- u32 sbintvec; /* interrupt mask */
- u32 sbtmstatelow; /* target state */
- u32 sbtmstatehigh; /* target state */
- u32 sbbwa0; /* bandwidth allocation table0 */
- u32 PAD;
- u32 sbimconfiglow; /* initiator configuration */
- u32 sbimconfighigh; /* initiator configuration */
- u32 sbadmatch0; /* address match0 */
- u32 PAD;
- u32 sbtmconfiglow; /* target configuration */
- u32 sbtmconfighigh; /* target configuration */
- u32 sbbconfig; /* broadcast configuration */
- u32 PAD;
- u32 sbbstate; /* broadcast state */
- u32 PAD[3];
- u32 sbactcnfg; /* activate configuration */
- u32 PAD[3];
- u32 sbflagst; /* current sbflags */
- u32 PAD[3];
- u32 sbidlow; /* identification */
- u32 sbidhigh; /* identification */
-} sbconfig_t;
-
-#endif /* _LANGUAGE_ASSEMBLY */
-
-/* sbipsflag */
-#define SBIPS_INT1_MASK 0x3f /* which sbflags get routed to mips interrupt 1 */
-#define SBIPS_INT1_SHIFT 0
-#define SBIPS_INT2_MASK 0x3f00 /* which sbflags get routed to mips interrupt 2 */
-#define SBIPS_INT2_SHIFT 8
-#define SBIPS_INT3_MASK 0x3f0000 /* which sbflags get routed to mips interrupt 3 */
-#define SBIPS_INT3_SHIFT 16
-#define SBIPS_INT4_MASK 0x3f000000 /* which sbflags get routed to mips interrupt 4 */
-#define SBIPS_INT4_SHIFT 24
-
-/* sbtpsflag */
-#define SBTPS_NUM0_MASK 0x3f /* interrupt sbFlag # generated by this core */
-#define SBTPS_F0EN0 0x40 /* interrupt is always sent on the backplane */
-
-/* sbtmerrlog */
-#define SBTMEL_CM 0x00000007 /* command */
-#define SBTMEL_CI 0x0000ff00 /* connection id */
-#define SBTMEL_EC 0x0f000000 /* error code */
-#define SBTMEL_ME 0x80000000 /* multiple error */
-
-/* sbimstate */
-#define SBIM_PC 0xf /* pipecount */
-#define SBIM_AP_MASK 0x30 /* arbitration policy */
-#define SBIM_AP_BOTH 0x00 /* use both timeslaces and token */
-#define SBIM_AP_TS 0x10 /* use timesliaces only */
-#define SBIM_AP_TK 0x20 /* use token only */
-#define SBIM_AP_RSV 0x30 /* reserved */
-#define SBIM_IBE 0x20000 /* inbanderror */
-#define SBIM_TO 0x40000 /* timeout */
-#define SBIM_BY 0x01800000 /* busy (sonics >= 2.3) */
-#define SBIM_RJ 0x02000000 /* reject (sonics >= 2.3) */
-
-/* sbtmstatelow */
-#define SBTML_RESET 0x0001 /* reset */
-#define SBTML_REJ_MASK 0x0006 /* reject field */
-#define SBTML_REJ 0x0002 /* reject */
-#define SBTML_TMPREJ 0x0004 /* temporary reject, for error recovery */
-
-#define SBTML_SICF_SHIFT 16 /* Shift to locate the SI control flags in sbtml */
-
-/* sbtmstatehigh */
-#define SBTMH_SERR 0x0001 /* serror */
-#define SBTMH_INT 0x0002 /* interrupt */
-#define SBTMH_BUSY 0x0004 /* busy */
-#define SBTMH_TO 0x0020 /* timeout (sonics >= 2.3) */
-
-#define SBTMH_SISF_SHIFT 16 /* Shift to locate the SI status flags in sbtmh */
-
-/* sbbwa0 */
-#define SBBWA_TAB0_MASK 0xffff /* lookup table 0 */
-#define SBBWA_TAB1_MASK 0xffff /* lookup table 1 */
-#define SBBWA_TAB1_SHIFT 16
-
-/* sbimconfiglow */
-#define SBIMCL_STO_MASK 0x7 /* service timeout */
-#define SBIMCL_RTO_MASK 0x70 /* request timeout */
-#define SBIMCL_RTO_SHIFT 4
-#define SBIMCL_CID_MASK 0xff0000 /* connection id */
-#define SBIMCL_CID_SHIFT 16
-
-/* sbimconfighigh */
-#define SBIMCH_IEM_MASK 0xc /* inband error mode */
-#define SBIMCH_TEM_MASK 0x30 /* timeout error mode */
-#define SBIMCH_TEM_SHIFT 4
-#define SBIMCH_BEM_MASK 0xc0 /* bus error mode */
-#define SBIMCH_BEM_SHIFT 6
-
-/* sbadmatch0 */
-#define SBAM_TYPE_MASK 0x3 /* address type */
-#define SBAM_AD64 0x4 /* reserved */
-#define SBAM_ADINT0_MASK 0xf8 /* type0 size */
-#define SBAM_ADINT0_SHIFT 3
-#define SBAM_ADINT1_MASK 0x1f8 /* type1 size */
-#define SBAM_ADINT1_SHIFT 3
-#define SBAM_ADINT2_MASK 0x1f8 /* type2 size */
-#define SBAM_ADINT2_SHIFT 3
-#define SBAM_ADEN 0x400 /* enable */
-#define SBAM_ADNEG 0x800 /* negative decode */
-#define SBAM_BASE0_MASK 0xffffff00 /* type0 base address */
-#define SBAM_BASE0_SHIFT 8
-#define SBAM_BASE1_MASK 0xfffff000 /* type1 base address for the core */
-#define SBAM_BASE1_SHIFT 12
-#define SBAM_BASE2_MASK 0xffff0000 /* type2 base address for the core */
-#define SBAM_BASE2_SHIFT 16
-
-/* sbtmconfiglow */
-#define SBTMCL_CD_MASK 0xff /* clock divide */
-#define SBTMCL_CO_MASK 0xf800 /* clock offset */
-#define SBTMCL_CO_SHIFT 11
-#define SBTMCL_IF_MASK 0xfc0000 /* interrupt flags */
-#define SBTMCL_IF_SHIFT 18
-#define SBTMCL_IM_MASK 0x3000000 /* interrupt mode */
-#define SBTMCL_IM_SHIFT 24
-
-/* sbtmconfighigh */
-#define SBTMCH_BM_MASK 0x3 /* busy mode */
-#define SBTMCH_RM_MASK 0x3 /* retry mode */
-#define SBTMCH_RM_SHIFT 2
-#define SBTMCH_SM_MASK 0x30 /* stop mode */
-#define SBTMCH_SM_SHIFT 4
-#define SBTMCH_EM_MASK 0x300 /* sb error mode */
-#define SBTMCH_EM_SHIFT 8
-#define SBTMCH_IM_MASK 0xc00 /* int mode */
-#define SBTMCH_IM_SHIFT 10
-
-/* sbbconfig */
-#define SBBC_LAT_MASK 0x3 /* sb latency */
-#define SBBC_MAX0_MASK 0xf0000 /* maxccntr0 */
-#define SBBC_MAX0_SHIFT 16
-#define SBBC_MAX1_MASK 0xf00000 /* maxccntr1 */
-#define SBBC_MAX1_SHIFT 20
-
-/* sbbstate */
-#define SBBS_SRD 0x1 /* st reg disable */
-#define SBBS_HRD 0x2 /* hold reg disable */
-
-/* sbidlow */
-#define SBIDL_CS_MASK 0x3 /* config space */
-#define SBIDL_AR_MASK 0x38 /* # address ranges supported */
-#define SBIDL_AR_SHIFT 3
-#define SBIDL_SYNCH 0x40 /* sync */
-#define SBIDL_INIT 0x80 /* initiator */
-#define SBIDL_MINLAT_MASK 0xf00 /* minimum backplane latency */
-#define SBIDL_MINLAT_SHIFT 8
-#define SBIDL_MAXLAT 0xf000 /* maximum backplane latency */
-#define SBIDL_MAXLAT_SHIFT 12
-#define SBIDL_FIRST 0x10000 /* this initiator is first */
-#define SBIDL_CW_MASK 0xc0000 /* cycle counter width */
-#define SBIDL_CW_SHIFT 18
-#define SBIDL_TP_MASK 0xf00000 /* target ports */
-#define SBIDL_TP_SHIFT 20
-#define SBIDL_IP_MASK 0xf000000 /* initiator ports */
-#define SBIDL_IP_SHIFT 24
-#define SBIDL_RV_MASK 0xf0000000 /* sonics backplane revision code */
-#define SBIDL_RV_SHIFT 28
-#define SBIDL_RV_2_2 0x00000000 /* version 2.2 or earlier */
-#define SBIDL_RV_2_3 0x10000000 /* version 2.3 */
-
-/* sbidhigh */
-#define SBIDH_RC_MASK 0x000f /* revision code */
-#define SBIDH_RCE_MASK 0x7000 /* revision code extension field */
-#define SBIDH_RCE_SHIFT 8
-#define SBCOREREV(sbidh) \
- ((((sbidh) & SBIDH_RCE_MASK) >> SBIDH_RCE_SHIFT) | ((sbidh) & SBIDH_RC_MASK))
-#define SBIDH_CC_MASK 0x8ff0 /* core code */
-#define SBIDH_CC_SHIFT 4
-#define SBIDH_VC_MASK 0xffff0000 /* vendor code */
-#define SBIDH_VC_SHIFT 16
-
-#define SB_COMMIT 0xfd8 /* update buffered registers value */
-
-/* vendor codes */
-#define SB_VEND_BCM 0x4243 /* Broadcom's SB vendor code */
#endif /* _SBCONFIG_H */
/* 32 bits addressing */
-/* dma registers per channel(xmt or rcv) */
-typedef volatile struct {
- u32 control; /* enable, et al */
- u32 addr; /* descriptor ring base address (4K aligned) */
- u32 ptr; /* last descriptor posted to chip */
- u32 status; /* current active descriptor, et al */
-} dma32regs_t;
-
-typedef volatile struct {
- dma32regs_t xmt; /* dma tx channel */
- dma32regs_t rcv; /* dma rx channel */
-} dma32regp_t;
-
typedef volatile struct { /* diag access */
u32 fifoaddr; /* diag address */
u32 fifodatalow; /* low 32bits of data */
u32 pad; /* reserved */
} dma32diag_t;
-/*
- * DMA Descriptor
- * Descriptors are only read by the hardware, never written back.
- */
-typedef volatile struct {
- u32 ctrl; /* misc control bits & bufcount */
- u32 addr; /* data buffer address */
-} dma32dd_t;
-
-/*
- * Each descriptor ring must be 4096byte aligned, and fit within a single 4096byte page.
- */
-#define D32RINGALIGN_BITS 12
-#define D32MAXRINGSZ (1 << D32RINGALIGN_BITS)
-#define D32RINGALIGN (1 << D32RINGALIGN_BITS)
-
-#define D32MAXDD (D32MAXRINGSZ / sizeof (dma32dd_t))
-
-/* transmit channel control */
-#define XC_XE ((u32)1 << 0) /* transmit enable */
-#define XC_SE ((u32)1 << 1) /* transmit suspend request */
-#define XC_LE ((u32)1 << 2) /* loopback enable */
-#define XC_FL ((u32)1 << 4) /* flush request */
-#define XC_PD ((u32)1 << 11) /* parity check disable */
-#define XC_AE ((u32)3 << 16) /* address extension bits */
-#define XC_AE_SHIFT 16
-
-/* transmit descriptor table pointer */
-#define XP_LD_MASK 0xfff /* last valid descriptor */
-
-/* transmit channel status */
-#define XS_CD_MASK 0x0fff /* current descriptor pointer */
-#define XS_XS_MASK 0xf000 /* transmit state */
-#define XS_XS_SHIFT 12
-#define XS_XS_DISABLED 0x0000 /* disabled */
-#define XS_XS_ACTIVE 0x1000 /* active */
-#define XS_XS_IDLE 0x2000 /* idle wait */
-#define XS_XS_STOPPED 0x3000 /* stopped */
-#define XS_XS_SUSP 0x4000 /* suspend pending */
-#define XS_XE_MASK 0xf0000 /* transmit errors */
-#define XS_XE_SHIFT 16
-#define XS_XE_NOERR 0x00000 /* no error */
-#define XS_XE_DPE 0x10000 /* descriptor protocol error */
-#define XS_XE_DFU 0x20000 /* data fifo underrun */
-#define XS_XE_BEBR 0x30000 /* bus error on buffer read */
-#define XS_XE_BEDA 0x40000 /* bus error on descriptor access */
-#define XS_AD_MASK 0xfff00000 /* active descriptor */
-#define XS_AD_SHIFT 20
-
-/* receive channel control */
-#define RC_RE ((u32)1 << 0) /* receive enable */
-#define RC_RO_MASK 0xfe /* receive frame offset */
-#define RC_RO_SHIFT 1
-#define RC_FM ((u32)1 << 8) /* direct fifo receive (pio) mode */
-#define RC_SH ((u32)1 << 9) /* separate rx header descriptor enable */
-#define RC_OC ((u32)1 << 10) /* overflow continue */
-#define RC_PD ((u32)1 << 11) /* parity check disable */
-#define RC_AE ((u32)3 << 16) /* address extension bits */
-#define RC_AE_SHIFT 16
-
-/* receive descriptor table pointer */
-#define RP_LD_MASK 0xfff /* last valid descriptor */
-
-/* receive channel status */
-#define RS_CD_MASK 0x0fff /* current descriptor pointer */
-#define RS_RS_MASK 0xf000 /* receive state */
-#define RS_RS_SHIFT 12
-#define RS_RS_DISABLED 0x0000 /* disabled */
-#define RS_RS_ACTIVE 0x1000 /* active */
-#define RS_RS_IDLE 0x2000 /* idle wait */
-#define RS_RS_STOPPED 0x3000 /* reserved */
-#define RS_RE_MASK 0xf0000 /* receive errors */
-#define RS_RE_SHIFT 16
-#define RS_RE_NOERR 0x00000 /* no error */
-#define RS_RE_DPE 0x10000 /* descriptor protocol error */
-#define RS_RE_DFO 0x20000 /* data fifo overflow */
-#define RS_RE_BEBW 0x30000 /* bus error on buffer write */
-#define RS_RE_BEDA 0x40000 /* bus error on descriptor access */
-#define RS_AD_MASK 0xfff00000 /* active descriptor */
-#define RS_AD_SHIFT 20
-
-/* fifoaddr */
-#define FA_OFF_MASK 0xffff /* offset */
-#define FA_SEL_MASK 0xf0000 /* select */
-#define FA_SEL_SHIFT 16
-#define FA_SEL_XDD 0x00000 /* transmit dma data */
-#define FA_SEL_XDP 0x10000 /* transmit dma pointers */
-#define FA_SEL_RDD 0x40000 /* receive dma data */
-#define FA_SEL_RDP 0x50000 /* receive dma pointers */
-#define FA_SEL_XFD 0x80000 /* transmit fifo data */
-#define FA_SEL_XFP 0x90000 /* transmit fifo pointers */
-#define FA_SEL_RFD 0xc0000 /* receive fifo data */
-#define FA_SEL_RFP 0xd0000 /* receive fifo pointers */
-#define FA_SEL_RSD 0xe0000 /* receive frame status data */
-#define FA_SEL_RSP 0xf0000 /* receive frame status pointers */
-
-/* descriptor control flags */
-#define CTRL_BC_MASK 0x00001fff /* buffer byte count, real data len must <= 4KB */
-#define CTRL_AE ((u32)3 << 16) /* address extension bits */
-#define CTRL_AE_SHIFT 16
-#define CTRL_PARITY ((u32)3 << 18) /* parity bit */
-#define CTRL_EOT ((u32)1 << 28) /* end of descriptor table */
-#define CTRL_IOC ((u32)1 << 29) /* interrupt on completion */
-#define CTRL_EOF ((u32)1 << 30) /* end of frame */
-#define CTRL_SOF ((u32)1 << 31) /* start of frame */
-
-/* control flags in the range [27:20] are core-specific and not defined here */
-#define CTRL_CORE_MASK 0x0ff00000
-
/* 64 bits addressing */
/* dma registers per channel(xmt or rcv) */
u32 status1; /* active descriptor, xmt error */
} dma64regs_t;
-typedef volatile struct {
- dma64regs_t tx; /* dma64 tx channel */
- dma64regs_t rx; /* dma64 rx channel */
-} dma64regp_t;
-
-typedef volatile struct { /* diag access */
- u32 fifoaddr; /* diag address */
- u32 fifodatalow; /* low 32bits of data */
- u32 fifodatahigh; /* high 32bits of data */
- u32 pad; /* reserved */
-} dma64diag_t;
-
-/*
- * DMA Descriptor
- * Descriptors are only read by the hardware, never written back.
- */
-typedef volatile struct {
- u32 ctrl1; /* misc control bits & bufcount */
- u32 ctrl2; /* buffer count and address extension */
- u32 addrlow; /* memory address of the date buffer, bits 31:0 */
- u32 addrhigh; /* memory address of the date buffer, bits 63:32 */
-} dma64dd_t;
-
-/*
- * Each descriptor ring must be 8kB aligned, and fit within a contiguous 8kB physical address.
- */
-#define D64RINGALIGN_BITS 13
-#define D64MAXRINGSZ (1 << D64RINGALIGN_BITS)
-#define D64RINGALIGN (1 << D64RINGALIGN_BITS)
-
-#define D64MAXDD (D64MAXRINGSZ / sizeof (dma64dd_t))
-
-/* transmit channel control */
-#define D64_XC_XE 0x00000001 /* transmit enable */
-#define D64_XC_SE 0x00000002 /* transmit suspend request */
-#define D64_XC_LE 0x00000004 /* loopback enable */
-#define D64_XC_FL 0x00000010 /* flush request */
-#define D64_XC_PD 0x00000800 /* parity check disable */
-#define D64_XC_AE 0x00030000 /* address extension bits */
-#define D64_XC_AE_SHIFT 16
-
-/* transmit descriptor table pointer */
-#define D64_XP_LD_MASK 0x00000fff /* last valid descriptor */
-
-/* transmit channel status */
-#define D64_XS0_CD_MASK 0x00001fff /* current descriptor pointer */
-#define D64_XS0_XS_MASK 0xf0000000 /* transmit state */
-#define D64_XS0_XS_SHIFT 28
-#define D64_XS0_XS_DISABLED 0x00000000 /* disabled */
-#define D64_XS0_XS_ACTIVE 0x10000000 /* active */
-#define D64_XS0_XS_IDLE 0x20000000 /* idle wait */
-#define D64_XS0_XS_STOPPED 0x30000000 /* stopped */
-#define D64_XS0_XS_SUSP 0x40000000 /* suspend pending */
-
-#define D64_XS1_AD_MASK 0x00001fff /* active descriptor */
-#define D64_XS1_XE_MASK 0xf0000000 /* transmit errors */
-#define D64_XS1_XE_SHIFT 28
-#define D64_XS1_XE_NOERR 0x00000000 /* no error */
-#define D64_XS1_XE_DPE 0x10000000 /* descriptor protocol error */
-#define D64_XS1_XE_DFU 0x20000000 /* data fifo underrun */
-#define D64_XS1_XE_DTE 0x30000000 /* data transfer error */
-#define D64_XS1_XE_DESRE 0x40000000 /* descriptor read error */
-#define D64_XS1_XE_COREE 0x50000000 /* core error */
-
-/* receive channel control */
-#define D64_RC_RE 0x00000001 /* receive enable */
-#define D64_RC_RO_MASK 0x000000fe /* receive frame offset */
-#define D64_RC_RO_SHIFT 1
-#define D64_RC_FM 0x00000100 /* direct fifo receive (pio) mode */
-#define D64_RC_SH 0x00000200 /* separate rx header descriptor enable */
-#define D64_RC_OC 0x00000400 /* overflow continue */
-#define D64_RC_PD 0x00000800 /* parity check disable */
-#define D64_RC_AE 0x00030000 /* address extension bits */
-#define D64_RC_AE_SHIFT 16
-
-/* flags for dma controller */
-#define DMA_CTRL_PEN (1 << 0) /* partity enable */
-#define DMA_CTRL_ROC (1 << 1) /* rx overflow continue */
-#define DMA_CTRL_RXMULTI (1 << 2) /* allow rx scatter to multiple descriptors */
-#define DMA_CTRL_UNFRAMED (1 << 3) /* Unframed Rx/Tx data */
-
-/* receive descriptor table pointer */
-#define D64_RP_LD_MASK 0x00000fff /* last valid descriptor */
-
-/* receive channel status */
-#define D64_RS0_CD_MASK 0x00001fff /* current descriptor pointer */
-#define D64_RS0_RS_MASK 0xf0000000 /* receive state */
-#define D64_RS0_RS_SHIFT 28
-#define D64_RS0_RS_DISABLED 0x00000000 /* disabled */
-#define D64_RS0_RS_ACTIVE 0x10000000 /* active */
-#define D64_RS0_RS_IDLE 0x20000000 /* idle wait */
-#define D64_RS0_RS_STOPPED 0x30000000 /* stopped */
-#define D64_RS0_RS_SUSP 0x40000000 /* suspend pending */
-
-#define D64_RS1_AD_MASK 0x0001ffff /* active descriptor */
-#define D64_RS1_RE_MASK 0xf0000000 /* receive errors */
-#define D64_RS1_RE_SHIFT 28
-#define D64_RS1_RE_NOERR 0x00000000 /* no error */
-#define D64_RS1_RE_DPO 0x10000000 /* descriptor protocol error */
-#define D64_RS1_RE_DFU 0x20000000 /* data fifo overflow */
-#define D64_RS1_RE_DTE 0x30000000 /* data transfer error */
-#define D64_RS1_RE_DESRE 0x40000000 /* descriptor read error */
-#define D64_RS1_RE_COREE 0x50000000 /* core error */
-
-/* fifoaddr */
-#define D64_FA_OFF_MASK 0xffff /* offset */
-#define D64_FA_SEL_MASK 0xf0000 /* select */
-#define D64_FA_SEL_SHIFT 16
-#define D64_FA_SEL_XDD 0x00000 /* transmit dma data */
-#define D64_FA_SEL_XDP 0x10000 /* transmit dma pointers */
-#define D64_FA_SEL_RDD 0x40000 /* receive dma data */
-#define D64_FA_SEL_RDP 0x50000 /* receive dma pointers */
-#define D64_FA_SEL_XFD 0x80000 /* transmit fifo data */
-#define D64_FA_SEL_XFP 0x90000 /* transmit fifo pointers */
-#define D64_FA_SEL_RFD 0xc0000 /* receive fifo data */
-#define D64_FA_SEL_RFP 0xd0000 /* receive fifo pointers */
-#define D64_FA_SEL_RSD 0xe0000 /* receive frame status data */
-#define D64_FA_SEL_RSP 0xf0000 /* receive frame status pointers */
-
-/* descriptor control flags 1 */
-#define D64_CTRL_COREFLAGS 0x0ff00000 /* core specific flags */
-#define D64_CTRL1_EOT ((u32)1 << 28) /* end of descriptor table */
-#define D64_CTRL1_IOC ((u32)1 << 29) /* interrupt on completion */
-#define D64_CTRL1_EOF ((u32)1 << 30) /* end of frame */
-#define D64_CTRL1_SOF ((u32)1 << 31) /* start of frame */
-
-/* descriptor control flags 2 */
-#define D64_CTRL2_BC_MASK 0x00007fff /* buffer byte count. real data len must <= 16KB */
-#define D64_CTRL2_AE 0x00030000 /* address extension bits */
-#define D64_CTRL2_AE_SHIFT 16
-#define D64_CTRL2_PARITY 0x00040000 /* parity bit */
-
-/* control flags in the range [27:20] are core-specific and not defined here */
-#define D64_CTRL_CORE_MASK 0x0ff00000
-
-#define D64_RX_FRM_STS_LEN 0x0000ffff /* frame length mask */
-#define D64_RX_FRM_STS_OVFL 0x00800000 /* RxOverFlow */
-#define D64_RX_FRM_STS_DSCRCNT 0x0f000000 /* no. of descriptors used - 1 */
-#define D64_RX_FRM_STS_DATATYPE 0xf0000000 /* core-dependent data type */
-
-/* receive frame status */
-typedef volatile struct {
- u16 len;
- u16 flags;
-} dma_rxh_t;
-
#endif /* _sbdma_h_ */